- 您現在的位置：買賣IC網 > PDF目錄3291 > ISL28268FUZ (Intersil)IC OP AMP DUAL RRIO 34UA 8-MSOP PDF資料下載
參數資料
| 型號： | ISL28268FUZ |
| 廠商： | Intersil |
| 文件頁數： | 5/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OP AMP DUAL RRIO 34UA 8-MSOP |
| 標準包裝： | 50 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.1 V/µs |
| 增益帶寬積： | 200kHz |
| -3db帶寬： | 420kHz |
| 電流 - 輸入偏壓： | 10pA |
| 電壓 - 輸入偏移： | 90µV |
| 電流 - 電源： | 34µA |
| 電流 - 輸出 / 通道： | 30mA |
| 電壓 - 電源，單路/雙路(±)： | 2.4 V ~ 5.5 V，±1.2 V ~ 2.75 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1234 (CN2011-ZH PDF) |
13
FN6378.4
July 25, 2011
2. The output current required is higher than the output
stage can deliver. These conditions can result in a shift in
the Input Offset Voltage (VOS) as much as 1V/hr. of
exposure under these conditions.
IN+ and IN- Input Protection
All input terminals have internal ESD protection diodes to both
positive and negative supply rails, limiting the input voltage to
within one diode beyond the supply rails. They also contain
back-to-back diodes across the input terminals (see “Pin
the input differential voltage is expected to exceed 0.5V, an
external series resistor must be used to ensure the input
currents never exceed 5mA (see Figure 41).
Enable/Disable Feature
The ISL28168 offers an EN pin that disables the device
when pulled up to at least 2.0V. In the disabled state (output
in a high impedance state), the part consumes typically 10A
at room temperature. By disabling the part, multiple
ISL28168 parts can be connected together as a MUX. In this
configuration, the outputs are tied together in parallel and a
channel can be selected by the EN pin. The loading effects
of the feedback resistors of the disabled amplifier must be
considered when multiple amplifier outputs are connected
together. Note that feed through from the IN+ to IN- pins
occurs on any Mux Amp disabled channel where the input
differential voltage exceeds 0.5V (e.g., active channel
VOUT = 1V, while disabled channel VIN = GND), so the Mux
implementation is best suited for small signal applications. If
large signals are required, use series IN+ resistors, or large
value RF, to keep the feed-through current low enough to
minimize the impact on the active channel. See “Limitations
details.
To disable the part, the user needs to supply the 1.5A
required to pull the EN pin to the V+ rail. If left open, the EN
pin will pull to the negative rail and the device will be enabled
by default. If the EN function is not required (no need to turn
the part off), as a precaution, it is recommended that the
user tie the EN pin to the V- pin.
Limitations of the Differential Input Protection
If the input differential voltage is expected to exceed 0.5V, an
external current limiting resistor must be used to ensure the
input current never exceeds 5mA. For non inverting unity
gain applications, the current limiting can be via a series IN+
resistor, or via a feedback resistor of appropriate value. For
other gain configurations, the series IN+ resistor is the best
choice, unless the feedback (RF) and gain setting (RG)
resistors are both sufficiently large to limit the input current to
5mA.
Large differential input voltages can arise from several
sources:
1. During open loop (comparator) operation. Used this way,
the IN+ and IN- voltages don’t track, so differentials arise.
2. When the amplifier is disabled but an input signal is still
present. An RL or RG to GND keeps the IN- at GND, while
the varying IN+ signal creates a differential voltage. Mux
Amp applications are similar, except that the active
channel VOUT determines the voltage on the IN- terminal.
3. When the slew rate of the input pulse is considerably
faster than the op amp’s slew rate. If the VOUT can’t keep
up with the IN+ signal, a differential voltage results, and
visible distortion occurs on the input and output signals.
To avoid this issue, keep the input slew rate below
0.1V/s, or use appropriate current limiting resistors.
Large (>2V) differential input voltages can also cause an
increase in disabled ICC.
The ISL28268 is a dual op amp. If the application only
requires one channel, the user must configure the unused
channel to prevent it from oscillating. The unused channel
will oscillate if the input and output pins are floating. This will
result in higher than expected supply currents and possible
noise injection into the channel being used. The proper way
to prevent this oscillation is to short the output to the
negative input and ground the positive input (as shown in
Figure 42).
Proper Layout Maximizes Performance
To achieve the maximum performance of the high input
impedance and low offset voltage, care should be taken in
the circuit board layout. The PC board surface must remain
clean and free of moisture to avoid leakage currents
between adjacent traces. Surface coating of the circuit board
will reduce surface moisture and provide a humidity barrier,
reducing parasitic resistance on the board. When input
leakage current is a concern, the use of guard rings around
the amplifier inputs will further reduce leakage currents.
Figure 43 shows a guard ring example for a unity gain
amplifier that uses the low impedance amplifier output at the
same voltage as the high impedance input to eliminate
surface leakage. The guard ring does not need to be a
specific width, but it should form a continuous loop around
both inputs. For further reduction of leakage currents,
FIGURE 41. INPUT CURRENT LIMITING
-
+
RIN
RL
VIN
VOUT
FIGURE 42. PREVENTING OSCILLATIONS IN UNUSED
CHANNELS
-
+
ISL28168, ISL28268
相關PDF資料 |
PDF描述 |
|---|---|
| 1-535584-4 | CONN RCPT 15POS .100 TIN LEAD |
| 0459848241 | CONN RCPT R/A 8PWR 24SGL 3.18MM |
| 146140-5 | CONN RCPT 12POS DL R/A .100 T/H |
| 0741620414 | CONN RCPT R/A 14POS 2.54MM GOLD |
| 535585-7 | CONN RCPT 14POS DUAL VERT .100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL28268FUZ-T7 | 功能描述:IC OP AMP DUAL RRIO 34UA 8-MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR |
| ISL28268MSOPEVAL1Z | 功能描述:EVALUATION BOARD ISL28268 8MSOP RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| ISL28268SOICEVAL1Z | 功能描述:EVALUATION BOARD ISL28268 8SOIC RoHS:是 類別:編程器，開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| ISL28270 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual and Quad Channel Micropower Single Supply, Rail-to-Rail Input and Output RRIO Instrumentation Amplifiers |
| ISL28270_0708 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual and Quad Channel Micropower, Single Supply, Rail-to-Rail Input and Output (RRIO) Instrumentation Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。