- 您現在的位置：買賣IC網 > PDF目錄1926 > ISL22446WFRT20Z (Intersil)IC POT DGTL 128TP LN LP 20-TQFN PDF資料下載
參數資料
| 型號： | ISL22446WFRT20Z |
| 廠商： | Intersil |
| 文件頁數： | 4/15頁 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 128TP LN LP 20-TQFN |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 75 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 電阻（歐姆）： | 10k |
| 電路數： | 4 |
| 溫度系數： | 標準值 ±50 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 20-TQFN（4x4） |
| 包裝： | 管件 |
12
FN6181.2
September 9, 2009
All communication over the SPI interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
The first byte sent to the ISL22446 from the SPI host is the
Identification Byte. A valid Identification Byte contains 0101
as the four MSBs, with the following four bits set to 0.
TABLE 4. IDENTIFICATION BYTE FORMAT
The next byte sent to the ISL22446 contains the instruction
and register pointer information. The four MSBs are the
instruction and four LSBs are register address (see Table 5).
TABLE 5. IDENTIFICATION BYTE FORMAT
There are only two valid instruction sets:
1011(binary) - is a Read operation
1100(binary) - is a Write operation
Write Operation
A Write operation to the ISL22446 is a three-byte operation.
It first requires the CS transition from HIGH to LOW, then a
valid Identification Byte, then a valid instruction byte followed
by Data Byte is sent to SDI pin. The host terminates the write
operation by pulling the CS pin from LOW to HIGH. For a
write to addresses 0000b to 0011b, the MSB at address 8
(ACR[7]) determines if the Data Byte is to be written to
volatile or both volatile and non-volatile registers. Refer to
“Memory Description” on page 11 and Figure 16.
Device can receive more than one byte of data by auto
incrementing the address after each received byte. Note
after reaching the address 0110b, the internal pointer “rolls
over” to address 0000b.
The internal non-volatile write cycle starts after rising edge of
CS and takes up to 20ms. Thus, non-volatile registers must
be written individually.
Read Operation
A read operation to the ISL22446 is a three-byte operation. It
requires first, the CS transition from HIGH to LOW, then a
valid Identification Byte, then a valid instruction byte
following by “dummy” Data Byte is sent to SDI pin. The SPI
host reads the data from SDO pin on falling edge of SCK.
The host terminates the read operation by pulling the CS pin
from LOW to HIGH (see Figure 17).
The ISL22446 will provide the Data Bytes to the SDO pin as
long as SCK is provided by the host from the registers
indicated by an internal pointer. This pointer initial value is
determined by the register address in the Read operation
instruction, and increments by one during transmission of
each Data Byte. After reaching the memory location 0110b,
the pointer “rolls over” to 0000b, and the device continues to
output the data for each received SCK clock.
In order to read back the non-volatile IVR, it is recommended
that the application reads the ACR first to verify the WIP bit
is 0. If the WIP bit (ACR[5]) is not 0, the host should repeat
its reading sequence again.
01010000
(MSB)
(LSB)
76543210
I3
I2
I1
I0
R3
R2
R1
R0
0
1
0
1
0
I3
I2
I1
I0
R3
R2
R1 R0
SCK
SDI
0
D6
D5D4
D3
D2
D1D0
CS
00
0
FIGURE 16. THREE BYTE WRITE SEQUENCE
0
101
00
I3
I2
I1
I0
R3
R2
R1 R0
SCK
SDI
CS
00
SDO
0
D6
D5D4
D3
D2
D1D0
DON’T CARE
0
FIGURE 17. THREE BYTE READ SEQUENCE
ISL22446
相關PDF資料 |
PDF描述 |
|---|---|
| ISL22449UFV14Z-TK | IC POT DGTL 128TP LN LP 14-TSSOP |
| ISL22511UFB8Z | IC POT DGTL PB 32TP LN LP 8-SOIC |
| ISL22512WFB8Z | IC POT DGTL PB 16TP LN LP 8-SOIC |
| ISL23315WFUZ-TK | IC DGTL POT 256POS 10K 10MSOP |
| ISL23318WFUZ-TK | IC DGTL POT 1CH 10K 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL22446WFRT20Z-TK | 功能描述:數字電位計 IC 128 TAP FL RNG IND QD DCP 20LD 4X4 TQFN RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22446WFV20Z | 功能描述:數字電位計 IC 128 TAP FL RNG IND QD DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22446WFV20Z-TK | 功能描述:數字電位計 IC 128 TAP FL RNG IND QD DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22449 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digitally Controlled Potentiometer |
| ISL22449UFV14Z | 功能描述:IC POT DGTL 128TP LN LP 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。