- 您現在的位置：買賣IC網 > PDF目錄383128 > ISL22316 (Intersil Corporation) Low Noise, Low Power I2C Bus, 128 Taps(低噪聲,低功率，I2C總線, 128抽頭電位器) PDF資料下載
參數資料
| 型號： | ISL22316 |
| 廠商： | Intersil Corporation |
| 英文描述： | Low Noise, Low Power I2C Bus, 128 Taps(低噪聲,低功率，I2C總線, 128抽頭電位器) |
| 中文描述： | 低噪聲，低功耗I2C總線，128絲錐（低噪聲，低功率和I2C總線，128抽頭電位器） |
| 文件頁數： | 9/13頁 |
| 文件大小： | 483K |
| 代理商： | ISL22316 |
9
FN6186.0
June 23, 2006
Pin Description
Potentiometers Pins
RH and RL
The high (RH) and low (RL) terminals of the ISL22316 are
equivalent to the fixed terminals of a mechanical
potentiometer. RH and RL are referenced to the relative
position of the wiper and not the voltage potential on the
terminals. With WR set to 127 decimal, the wiper will be
closest to RH, and with the WR set to 0, the wiper is closest
to RL.
RW
RW is the wiper terminal and is equivalent to the movable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the WR register.
SHDN
The SHDN pin forces the resistor to end-to-end open circuit
condition on RH and shorts RW to RL. When SHDN is
returned to logic high, the previous latch settings put RWi at
the same resistance setting prior to shutdown. This pin is
logically OR’d with SHDN bit in ACR register. I
2
C interface is
still available in shutdown mode and all registers are
accessible. This pin must remain HIGH for normal operation.
Bus Interface Pins
Serial Data Input/Output (SDA)
The SDA is a bidirectional serial data input/output pin for I
2
C
interface. It receives device address, operation code, wiper
address and data from an I
2
C external master device at the
rising edge of the serial clock SCL, and it shifts out data after
each falling edge of the serial clock.
SDA requires an external pull-up resistor, since it is an open
drain input/output.
Serial Clock (SCL)
This input is the serial clock of the I
2
C serial interface. SCL
requires an external pull-up resistor, since it is an open drain
input.
Device Address (A1, A0)
The address inputs are used to set the least significant 2 bits
of the 7-bit I
2
C interface slave address. A match in the slave
address serial data stream must match with the Address
input pins in order to initiate communication with the
ISL22316. A maximum of four ISL22316 devices may
occupy the I
2
C serial bus.
Principles of Operation
The ISL22316 is an integrated circuit incorporating one DCP
with its associated registers, non-volatile memory and an I
2
C
serial interface providing direct communication between a
host and the potentiometer and memory. The resistor array
is comprised of individual resistors connected in series. At
either end of the array and between each resistor is an
electronic switch that transfers the potential at that point to
the wiper.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions.
FIGURE 13. MIDSCALE GLITCH, CODE 3Fh TO 40h
FIGURE 14. LARGE SIGNAL SETTLING TIME
Typical Performance Curves
(Continued)
Wiper Mid Point Movement
from 3Fh to 40h
RL
RW
RH
FIGURE 15. DCP CONNECTION IN SHUTDOWN MODE
ISL22316
相關PDF資料 |
PDF描述 |
|---|---|
| ISL22319 | Low Noise, Low Power, I2C Bus, 128 Taps, Wiper Only(低噪聲,低功率，I2C總線, 128抽頭電位器) |
| ISL22326 | Low Noise, Low Power, I2C Bus, 128 Taps(低噪聲,低功率，I2C總線, 128抽頭電位器) |
| ISL22329 | Low Noise, Low Power, I2C Bus, 128 Taps, Wiper Only(低噪聲,低功率，I2C總線, 128抽頭電位器) |
| ISL22346 | Low Noise, Low Power I2C Bus, 128 Taps(低噪聲,低功率，I2C總線, 128抽頭電位器) |
| ISL22349 | Low Noise, Low Power, I2C Bus, 128 Taps, Wiper Only(低噪聲,低功率，I2C總線, 128抽頭電位器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL22316UFRT10Z | 功能描述:數字電位計 IC 128 TAP FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22316UFRT10Z-TK | 功能描述:數字電位計 IC 128 TAP FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22316UFU10Z | 功能描述:數字電位計 IC 128 TAP FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22316UFU10Z-TK | 功能描述:數字電位計 IC 128 TAP FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22316WFRT10Z | 功能描述:數字電位計 IC 128 TAP FL RNG DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。