- 您現在的位置：買賣IC網 > PDF目錄9421 > ISL1221IUZ-T (Intersil)IC RTC LP BATT BACK SRAM 10MSOP PDF資料下載
參數資料
| 型號： | ISL1221IUZ-T |
| 廠商： | Intersil |
| 文件頁數： | 23/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC LP BATT BACK SRAM 10MSOP |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1 |
| 類型： | 時間事件記錄器 |
| 特點： | 警報器，閏年，SRAM |
| 存儲容量： | 2B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1245 (CN2011-ZH PDF) |
| 其它名稱： | ISL1221IUZ-TDKR |
8
FN6316.1
July 15, 2010
VBAT
This input provides a backup supply voltage to the device.
VBAT supplies power to the device in the event that the VDD
supply fails. This pin can be connected to a battery, a Super
Cap or tied to ground if not used.
EVIN (Event Input)
The EVIN pin is an input that is used to detect an externally
monitored event. When a high signal is present at the EVIN
pin, an “event” is detected. This input may be used for
various monitoring functions, such as the opening of a
detection switch on a chassis or door. The event detection
circuit can be user enabled or disabled (see EVEN bit) and
provides the option to be operational in battery backup
modes (see EVBATB bit). When the event detection is
disabled the EVIN pin is gated OFF. See“Functional
Description” on page 8 for more details.
FOUT (Frequency Output)
The FOUT pin outputs a clock signal which is related to the
crystal frequency. The frequency output is user selectable
and enabled via the I2C bus. It is an open drain active low
output. When not used, the output is high.
IRQ/EVDET (Alarm/Event Detect Output)
This dual function pin can be used as an interrupt alarm or
event detect output pin. Checking the status register will
show the type of interrupt, Alarm or Event Detect.
Interrupt Mode. The pin provides an interrupt signal
output. This signal notifies a host processor that an alarm
has occurred and requests action. It is an open drain
active low output.
The output will go low when an event is detected at the
EVIN pin. If the event detection function is enabled, the
IRQ/EVDET output will go low and stay low until the EVT
bit is cleared (see the EVIN pin description in the “Pin
Serial Clock (SCL)
The SCL input is used to clock all serial data into and out of
the device. The input buffer on this pin is always active (not
gated). It is disabled when the backup power supply on the
VBAT pin is activated to minimize power consumption.
Serial Data (SDA)
SDA is a bidirectional pin used to transfer data into and out
of the device. It has an open drain output and may be ORed
with other open drain or open collector outputs. The input
buffer is always active (not gated) in normal mode.
An open drain output requires the use of a pull-up resistor.
The output circuitry controls the fall time of the output signal
with the use of a slope controlled pull-down. The circuit is
designed for 400kHz I2C interface speeds. It is disabled
when the backup power supply on the VBAT pin is activated.
VDD, GND
Chip power supply and ground pins. The device will operate
with a power supply from VDD=2.7V to 5.5VDC. A 0.1F
capacitor is recommended on the VDD pin to ground.
Functional Description
Power Control Operation
The power control circuit accepts a VDD and a VBAT input.
Many types of batteries can be used with Intersil RTC
products. For example, 3.0V or 3.6V Lithium batteries are
appropriate, and battery sizes are available that can power
the ISL1221 for up to 10 years. Another option is to use a
Super Cap for applications where VDD is interrupted for up
to a month. See the “Application Section” on page 20 for
more information.
Normal Mode (VDD) to Battery Backup Mode
(VBAT)
To transition from the VDD to VBAT mode, both of the
following conditions must be met:
Condition 1:
VDD < VBAT - VBATHYS
where VBATHYS ≈ 50mV
Condition 2:
VDD < VTRIP
where VTRIP ≈ 2.2V
Battery Backup Mode (VBAT) to Normal Mode
(VDD)
The ISL1221 device will switch from the VBAT to VDD mode
when one of the following conditions occurs:
Condition 1:
VDD > VBAT + VBATHYS
where VBATHYS ≈ 50mV
Condition 2:
VDD > VTRIP + VTRIPHYS
where VTRIPHYS ≈ 30mV
These power control situations are illustrated in Figures 11
and 12.
FIGURE 10. RECOMMENDED CRYSTAL CONNECTION
X1
X2
ISL1221
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J1D-MZ | CONVERTER MOD DC/DC 85V 25W |
| VI-JNZ-EY-F4 | CONVERTER MOD DC/DC 2V 20W |
| VE-J1B-MZ | CONVERTER MOD DC/DC 95V 25W |
| VE-J14-MZ | CONVERTER MOD DC/DC 48V 25W |
| VI-JNZ-EY-F3 | CONVERTER MOD DC/DC 2V 20W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL14010 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Jitter Clock Generators for Set-Top Box |
| ISL14010IRZ | 功能描述:時鐘合成器/抖動清除器 REAL TIME CLKRTC 16LD 3X3 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| ISL14010IRZ-T | 功能描述:實時時鐘 REAL TIME CLKRTC 16LD 3X3 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL14011 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Jitter Clock Generators for Set-Top Box |
| ISL14011IRZ | 功能描述:時鐘合成器/抖動清除器 REAL TIME CLKRTC 16LD 3X3 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。