參數資料
型號： ISD5116SERIES
英文描述： Single-Chip Voice Record/Playback Device with Digital Memory Capability
中文描述： 單芯片語音記錄/回放和數字記憶能力的裝置
文件頁數： 72/81頁
文件大?。?/td> 2441K
代理商： ISD5116SERIES
ISD5116
10.5.
I
2
C Protocol
Since the I2C protocol allows multiple devices on the bus, each device must have an address. This
address is known as a “Slave Address”. A Slave Address consists of 7 bits, followed by a single bit
that indicates the direction of data flow. This single bit is 1 for a Write cycle, which indicates the data is
being sent from the current bus master to the device being addressed. This single bit is a 0 for a Read
cycle, which indicates that the data is being sent from the device being addressed to the current bus
master. For example, the valid Slave Addresses for the ISD5116 device, for both Write and Read
cycles, are shown in
section 7.3.1
on page 12 of this datasheet.
Before any data is transmitted on the I2C interface, the current bus master must address the slave it
wishes to transfer data to or from. The Slave Address is always sent out as the 1
st
byte following the
Start Condition sequence. An example of a Master transmitting an address to a ISD5116 slave is
shown below. In this case, the Master is writing data to the slave and the R/W bit is “0”, i.e. a Write
cycle. All the bits transferred are from the Master to the Slave, except for the indicated Acknowledge
bits. The following example details the transfer explained in
section 7.3.1
-
2
-
3
on pages 12-19 of this
datasheet
.
Master Transmits to Slave Receiver (Write) Mode
S
W A
A
A
A
P
SLAVE ADDRESS
COMMAND BYTE
High ADDR. BYTE
Low ADDR. BYTE
acknowledgement
from slave
acknowledgement
from slave
acknowledgement
from slave
acknowledgement
from slave
R/W
Start Bit
Stop Bit
A common procedure in the ISD5116 is the reading of the Status Bytes. The Read Status condition in
the ISD5116 is triggered when the Master addresses the chip with its proper Slave Address,
immediately followed by the R/W bit set to a “0” and without the Command Byte being sent. This is an
example of the Master sending to the Slave, immediately followed by the Slave sending data back to
the Master. The “N” not-acknowledge cycle from the Master ends the transfer of data from the Slave.
The following example details the transfer explained in
section 7.3.1
on page 12 of this datasheet.
- 72 -
相關PDF資料
PDF描述
ISD5216SERIES Single-Chip Voice Record/Playback Device
ISDMICROTAD-16M
ISDNRNYNG Optoelectronic
ISG4042-T 5V CATV MODEM RF TUNER AND TRANSMITTER
ISG4042EU-T 5V CATV MODEM RF TUNER AND TRANSMITTER
相關代理商/技術參數
參數描述
ISD5116SI 功能描述:IC VOICE REC/PL 8-16MN IN 28SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP（0.300"，7.62mm） 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD5116SIR 功能描述:IC VOICE REC/PL 8-16MN IN 28SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP（0.300"，7.62mm） 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD5116SY 功能描述:IC VOICE REC/PLAY 8-16MN 28-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP（0.300"，7.62mm） 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD5116SYI 功能描述:IC VOICE REC/PLAY 8-16MN 28-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP（0.300"，7.62mm） 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD5116SYIR 功能描述:IC VOICE REC/PLAY 8-16MN 28-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD5100 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP（0.300"，7.62mm） 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*