參數資料
型號: ISD2564X
廠商: WINBOND ELECTRONICS CORP
元件分類: 音頻合成
英文描述: SINGLE-CHIP, MULTIPLE-MESSAGES, VOICE RECORD/PLAYBACK DEVICE 32-, 40-, 48-, AND 64-SECOND DURATION
中文描述: 64 SEC, SPEECH SYNTHESIZER WITH RCDG, UUC28
封裝: DIE-28
文件頁數: 13/42頁
文件大?。?/td> 1356K
代理商: ISD2564X
ISD2532/40/48/64
M6 – Push-Button Mode
The ISD2500 series contain a Push-Button Operational Mode. The Push-Button Mode is used
primarily in very low-cost applications and is designed to minimize external circuitry and components,
thereby reducing system cost. In order to configure the device in Push-Button Operational Mode, the
two most significant address bits must be HIGH, and the M6 mode pin must also be HIGH. A device in
this mode always powers down at the end of each playback or record cycle after
CE
goes HIGH.
When this operational mode is implemented, three of the pins on the device have alternate
functionality as described in the table below.
TABLE 3: ALTERNATE FUNCTIONALITY IN PINS
Pin Name
Alternate Functionality in Push-Button Mode
CE
Start/Pause Push-Button (LOW pulse-activated)
PD
Stop/Reset Push-Button (HIGH pulse-activated)
EOM
Active-HIGH Run Indicator
CE
(START/PAUSE)
In Push-Button Operational Mode,
CE
acts as a LOW-going pulse-activated START/PAUSE signal.
If no operation is currently in progress, a LOW-going pulse on this signal will initiate a playback or
record cycle according to the level on the P/
R
pin. A subsequent pulse on the
CE
pin, before an
EOM
is reached in playback or an overflow condition occurs, will pause the current operation, and
the address counter is not reset. Another
CE
pulse will cause the device to continue the operation
from the place where it is paused.
PD (STOP/RESET)
In Push-Button Operational Mode, PD acts as a HIGH-going pulse-activated STOP/RESET signal.
When a playback or record cycle is in progress and a HIGH-going pulse is observed on PD, the
current cycle is terminated and the address pointer is reset to address 0, the beginning of the
message space.
EOM
(RUN)
In Push-Button Operational Mode,
EOM
becomes an active-HIGH RUN signal which can be used to
drive an LED or other external device. It is HIGH whenever a record or playback operation is in
progress.
Recording in Push-Button Mode
1. The PD pin should be LOW, usually using a pull-down resistor.
Publication Release Date: June 2003
- 13 -
Revision 1.0
相關PDF資料
PDF描述
ISD2540 Single-Chip Voice Record/Playback Device(Single-chip Durations of 40 seconds)(單片的錄音/錄音重放器(一片信息存儲持續時間40秒))
ISD2532 Single-Chip Voice Record/Playback Device(Single-chip Durations of 32 seconds)(單片的錄音/錄音重放器(一片信息存儲持續時間32秒))
ISD2564 Single-Chip Voice Record/Playback Device(Single-chip Durations of 64 seconds)(單片的錄音/錄音重放器(一片信息存儲持續時間64秒))
ISD2548 Single-Chip Voice Record/Playback Device(Single-chip Durations of 48 seconds)(單片的錄音/錄音重放器(一片信息存儲持續時間48秒))
ISD33075 Single-Chip Voice Record/Playback Devices 60-, 75-, 90-, and 120-Second Durations(單片聲音錄音/回放芯片(單片信息存儲持續時間75秒鐘))
相關代理商/技術參數
參數描述
ISD2575 制造商:WINBOND 制造商全稱:Winbond 功能描述:ISD2560
ISD2575E 功能描述:IC VOICE REC/PLAY 75-SEC 28-TSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD2500 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP(0.300",7.62mm) 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD2575EI 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single-Chip Voice Record/Playback Devices 32-, 40-, 48-, 64-,60-,75,90-, and 120-Second Durations
ISD2575ER 功能描述:IC VOICE REC/PLAY 75-SEC 28-TSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 語音錄制和重放 系列:ISD2500 標準包裝:14 系列:- 接口:串行 濾波器通頻帶:1.7kHz 持續時間:8 ~ 32 秒 安裝類型:通孔 封裝/外殼:28-DIP(0.300",7.62mm) 供應商設備封裝:28-PDIP 其它名稱:90-21300+000
ISD2575G 制造商:未知廠家 制造商全稱:未知廠家 功能描述: