- 您現在的位置：買賣IC網 > PDF目錄296249 > IRU1117CS (International Rectifier) 800mA LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR PDF資料下載
參數資料
| 型號： | IRU1117CS |
| 廠商： | International Rectifier |
| 英文描述： | 800mA LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR |
| 中文描述： | 800mA的低壓差型正，可調式穩壓器 |
| 文件頁數： | 5/10頁 |
| 文件大?。?/td> | 68K |
| 代理商： | IRU1117CS |
IRU1117
4
Rev. 1.8
02/04/03
www.irf.com
Output Voltage Setting
The IRU1117 can be programmed to any voltages in the
range of 1.25V to 5.5V with the addition of R1 and R2
external resistors according to the following formula:
Where:
VREF = 1.25V Typically
IADJ = 50
mA Typically
R1 and R2 as shown in Figure 3:
Figure 3 - Typical application of the IRU1117
for programming the output voltage.
The IRU1117 keeps a constant 1.25V between the out-
put pin and the adjust pin. By placing a resistor R1 across
these two pins a constant current flows through R1, add-
ing to the IADJ current and into the R2 resistor producing
a voltage equal to the (1.25/R1)
3R2 + IADJ3R2 which
will be added to the 1.25V to set the output voltage.
This is summarized in the above equation. Since the
minimum load current requirement of the IRU1117 is
10mA, R1 is typically selected to be 121
V resistor so
that it automatically satisfies the minimum current re-
quirement. Notice that since IADJ is typically in the range
of 50
mA it only adds a small error to the output voltage
and should only be considered when a very precise out-
put voltage setting is required. For example, in a typical
3.3V application where R1=121
V and R2=200V the er-
ror due to IADJ is only 0.3% of the nominal set point.
Load Regulation
Since the IRU1117 is only a three-terminal device, it is
not possible to provide true remote sensing of the output
voltage at the load. Figure 4 shows that the best load
regulation is achieved when the bottom side of R2 is
connected to the load and the top side of R1 resistor is
connected directly to the case or the VOUT pin of the
regulator and not to the load. In fact, if R1 is connected
to the load side, the effective resistance between the
regulator and the load is multiplied by the factor of (1+R2/
R1), or the effective resistance will be RP(eff)=RP
3(1+R2/
R1). It is important to note that for high current applica-
tions, this can represent a significant percentage of the
overall load regulation and one must keep the path from
the regulator to the load as short as possible to mini-
mize this effect.
Figure 4 - Schematic showing connection
for best load regulation.
Stability
The IRU1117 requires the use of an output capacitor as
part of the frequency compensation in order to make the
regulator stable. Typical designs for microprocessor ap-
plications use standard electrolytic capacitors with a
typical ESR in the range of 50 to 100m
V and an output
capacitance of 500 to 1000
mF. Fortunately as the ca-
pacitance increases, the ESR decreases resulting in a
fixed RC time constant. The IRU1117 takes advantage
of this phenomenon in making the overall regulator loop
stable. For most applications a minimum of 100
mF alu-
minum electrolytic capacitor such as Sanyo MVGX se-
ries, Panasonic FA series as well as the Nichicon PL
series insures both stability and good transient response.
Thermal Design
The IRU1117 incorporates an internal thermal shutdown
that protects the device when the junction temperature
exceeds the maximum allowable junction temperature.
Although this device can operate with junction tempera-
tures in the range of 150
8C, it is recommended that the
heat sink be selected such that during maximum con-
tinuous load operation the junction temperature is kept
below this number. The example below for a SCSI termi-
nator application shows the steps in selecting the proper
regulator in a surface-mount package. (See IRU1015 for
non-surface-mount packages)
VOUT
R1
R2
VIN
VREF
IADJ = 50uA
IRU1117
Adj
VOUT
VIN
R1
R2
VIN
RL
RP
PARASITICLINE
RESISTANCE
IRU1117
Adj
VOUT
VIN
VOUT = VREF
3 1+
+IADJ
3R2
R2
R1
(
)
相關PDF資料 |
PDF描述 |
|---|---|
| IS28F002BVT-80TI | 256K X 8 FLASH 5V PROM, 110 ns, PDSO40 |
| IS28F020-12PLI | 256K X 8 FLASH 12V PROM, 120 ns, PQCC32 |
| IS41LV44004-50JI | 4M X 4 EDO DRAM, 50 ns, PDSO24 |
| IS42VS16160D-75BLI | 16M X 16 SYNCHRONOUS DRAM, 5.4 ns, PBGA54 |
| IS45VS16160D-8BLA2 | 16M X 16 SYNCHRONOUS DRAM, 6 ns, PBGA54 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IRU1117CSTR | 功能描述:IC REG LDO ADJ .8A 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:500 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:12V 輸入電壓:14.5 V ~ 35 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:500mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-205AD，TO-39-3 金屬罐 供應商設備封裝:TO-39 包裝:散裝 其它名稱:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
| IRU1117CY | 功能描述:IC REG LDO ADJ .8A SOT-223 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:4V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.28V @ 150mA 穩壓器數量:1 電流 - 輸出:150mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:5-VFBGA 供應商設備封裝:5-uSMD 包裝:Digi-Reel® 其它名稱:LP2985AIBP-4.0DKR |
| IRU1117CYTR | 功能描述:IC REG LDO ADJ .8A SOT-223 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:500 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:12V 輸入電壓:14.5 V ~ 35 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:500mA 電流 - 限制（最小）:- 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-205AD，TO-39-3 金屬罐 供應商設備封裝:TO-39 包裝:散裝 其它名稱:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
| IRU1120 | 制造商:IRF 制造商全稱:International Rectifier 功能描述:2A LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR |
| IRU1120CP | 制造商:IRF 制造商全稱:International Rectifier 功能描述:2A LOW DROPOUT POSITIVE ADJUSTABLE REGULATOR |
發布緊急采購，3分鐘左右您將得到回復。