- 您現在的位置：買賣IC網 > PDF目錄383117 > IR3Y38 (Sharp Corporation) CCD Signal Process & Digital Interface IC PDF資料下載
參數資料
| 型號： | IR3Y38 |
| 廠商： | Sharp Corporation |
| 英文描述： | CCD Signal Process & Digital Interface IC |
| 中文描述： | CCD信號處理 |
| 文件頁數： | 12/21頁 |
| 文件大?。?/td> | 152K |
| 代理商： | IR3Y38 |
PRECAUTIONS
Each V
CC1
to V
CC6
pin corresponds to the each
GND
1
to GND
6
pin. Connect a ceramic capacitor
as near the IC as possible between each
corresponding V
CC
pin and GND pin.
The GND
1
pin is the ground of the CDS/ADC
circuit handling a weak signal. Pay careful attention
to the board layout of the GND
1
pattern in order to
avoid the potential fluctuation of the GND
1
caused
by the current of the other GND pins. Especially
pay attention to the current of the GND
6
pin's
flowing spiky current.
All the GND pins must be at the same potential
and not open. And keep the potential difference of
each V
CC
pin within 0.3 V.
The high level voltage of the outputs of the A/D
converter is controllable by the voltage of the
V
LOGIC
pin, but take care that the high level voltage
does not fall below about 1.5 V, in spite of making
the V
LOGIC
pin 0 V. This may cause the latch up of
the following logic ICs if the power supply of this IC
rises up faster than the power supply of the
following logic. To avoid this problem, it is
recommended to make the ‰ pin low until the
voltage of the logic power supply becomes stable.
Take care too that the high level voltage does not
rise above about V
CC
– 1.0 V, in spite of making
the V
LOGIC
pin the V
CC
potential.
Restore the value of the serial register when setting
up the power supply or making the ‰ pin high
because the value will have been removed in that
case.
IR3Y38M
12
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Supply voltage
Input voltage
Power consumption
(Unless otherwise specified, T
A
= +25 C)
CONDITIONS
SYMBOL
V
CC1
-V
CC6
V
IN
P
D
UNIT
V
V
mW
7
RATING
–0.3 to V
CC
+ 0.3
570
mW/C
C
C
4.5
T
A
> +25 C
T
A
≤ +25 C
P
D
derating ratio
Operating temperature
Storage temperature
T
OPR
T
STG
–30 to +70
–55 to +150
RECOMMENDED OPERATING CONDITIONS
PARAMETER
Supply voltage
Standard CCD input signal level
SYMBOL
V
CC1
-V
CC6
V
CCD
APPLICABLE PINS
UNIT
V
mVp-p
4.75 to 5.25
200
RATING
CCDIN
2.1 to V
CC
V
, SCK, SDATA,
‰, , fl/H
1
, fl/H
2
,
fl/H
3
, , ,
, fl/H
1
, fl/H
2
, fl/H
3
,
V
IH
Input "High" voltage
0 to 0.7
V
V
IL
Input "Low" voltage
≥ 12
≥ 1.5
ns
μs
t
WS/H
t
WC
S/H pulse width
Clamp pulse width
Serial interface clock frequency
f
SCK
SCK
kHz
≤ 300
A/D converter clock frequency
f
ADCK
ADCK
MHz
≤ 18
相關PDF資料 |
PDF描述 |
|---|---|
| IR3Y48 | TUBING TEFLON .018 ID 100' CLR |
| IR3Y48A1 | CCD SIGNAL PROCESS & DIGITAL INTERFACE IC |
| IR3Y48M | CCD Signal Process & Digital Interface IC |
| IR42-21C | 1.8MM ROUND SUBMINIATURE INFRARED LED |
| IR9022 | Low Power Dual Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IR3Y38M | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:CCD Signal Process & Digital Interface IC |
| IR3Y48 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:CCD Signal Process & Digital Interface IC |
| IR3Y48A1 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:CCD SIGNAL PROCESS & DIGITAL INTERFACE IC |
| IR3Y48M | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:CCD Signal Process & Digital Interface IC |
| IR-4 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Inductors Epoxy Conformal Coated Uniform Roll Coated |
發布緊急采購，3分鐘左右您將得到回復。