參數資料
| 型號： | IP82C54-10Z |
| 廠商： | Intersil |
| 文件頁數： | 7/22頁 |
| 文件大小： | 0K |
| 描述： | IC OSC PROG TIMER 10MHZ 24DIP |
| 標準包裝： | 165 |
| 類型： | 可編程計時器 |
| 頻率： | 10MHz |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電流 - 電源： | 10mA |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 24-DIP（0.600"，15.24mm） |
| 包裝： | 管件 |
| 供應商設備封裝： | 24-PDIP |
| 安裝類型： | 通孔 |
15
Counter will be loaded with new count on the next CLK pulse
and counting will continue from there.
Operation Common To All Modes
Programming
When a Control Word is written to a Counter, all Control
Logic, is immediately reset and OUT goes to a known initial
state; no CLK pulses are required for this.
Gate
The GATE input is always sampled on the rising edge of
CLK. In Modes 0, 2, 3 and 4 the GATE input is level
sensitive, and logic level is sampled on the rising edge of
CLK. In modes 1, 2, 3 and 5 the GATE input is rising-edge
sensitive. In these Modes, a rising edge of Gate (trigger)
sets an edge-sensitive flip-flop in the Counter. This flip-flop
is then sampled on the next rising edge of CLK. The flip-flop
is reset immediately after it is sampled. In this way, a trigger
will be detected no matter when it occurs - a high logic level
does not have to be maintained until the next rising edge of
CLK. Note that in Modes 2 and 3, the GATE input is both
edge-and level-sensitive.
Counter
New counts are loaded and Counters are decremented on
the falling edge of CLK.
The largest possible initial count is 0; this is equivalent to 216
for binary counting and 104 for BCD counting.
The counter does not stop when it reaches zero. In Modes 0,
1, 4, and 5 the Counter “wraps around” to the highest count,
either FFFF hex for binary counting or 9999 for BCD
counting, and continues counting. Modes 2 and 3 are
periodic; the Counter reloads itself with the initial count and
continues counting from there.
N
NNN
0
3
0
2
0
1
0
FF
0
3
WR
CLK
GATE
OUT
CW = 1A LSB = 3
NN
N
0
3
0
2
0
3
0
2
0
1
N
NNN
0
3
0
2
0
1
0
FF
FE
WR
CLK
GATE
OUT
CW = 1A LSB = 3
WR
CLK
GATE
OUT
CW = 1A LSB = 3
N
NN
0
FF
LSB = 5
N
0
5
0
4
FIGURE 14. MODE 5
SIGNAL
STATUS
MODES
LOW OR
GOING LOW
RISING
HIGH
0
Disables Counting
-
Enables Counting
1
-
1) Initiates
Counting
2) Resets output
after next clock
-
2
1) Disables
counting
2) Sets output
immediately high
Initiates Counting Enables Counting
3
1) Disables
counting
2) Sets output
immediately high
Initiates Counting Enables Counting
4
1) Disables
Counting
-
Enables Counting
5
-
Initiates Counting
-
FIGURE 15. GATE PIN OPERATIONS SUMMARY
MODE
MIN COUNT
MAX COUNT
010
110
220
320
410
510
NOTE: 0 is equivalent to 216 for binary counting and 104 for BCD
counting.
FIGURE 16. MINIMUM AND MAXIMUM INITIAL COUNTS
82C54
相關PDF資料 |
PDF描述 |
|---|---|
| MS27497E20F35PB | CONN RCPT 79POS WALL MNT W/PINS |
| MS27473T12F35P | CONN PLUG 22POS STRAIGHT W/PINS |
| MS27466T17F6PA | CONN RCPT 6POS WALL MT W/PINS |
| MS27466E17F6PA | CONN RCPT 6POS WALL MT W/PINS |
| MS27484E12A98PA | CONN PLUG 10POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IP82C54-12 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS Programmable Interval Timer |
| IP82C54Z | 功能描述:計時器和支持產品 W/ANNEAL PERIPH PRG- CNTR 5V 8MHZ RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| IP82C55A | 功能描述:外圍驅動器與原件 - PCI PERIPH PRG-I/O 5V 8MHZ IND RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| IP82C55A/+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral Interface |
| IP82C55A-5 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發(fā)布緊急采購，3分鐘左右您將得到回復。