參數資料
型號: INA326IDGKR
元件分類: 測量放大器
英文描述: INSTRUMENTATION AMPLIFIER|SINGLE|CMOS|TSSOP|8PIN|PLASTIC
中文描述: 儀表放大器|單|的CMOS | TSSOP封裝| 8引腳|塑料
文件頁數: 11/15頁
文件大?。?/td> 270K
代理商: INA326IDGKR
INA326, INA327
SBOS222
11
www.ti.com
FIGURE 5. Output Range Pedestal.
FIGURE 6. High-Side Shunt Measurement of Current Load.
FIGURE 7. Low-Side Shunt Measurement of Current Load.
FIGURE 8. Output Referenced to V
REF
/2.
FIGURE 9. Output from Pin 5 to Allow Swing Beyond the Rail.
FILTERING
Filtering can be adjusted through selection of R
2
C
2
and
R
O
C
O
for the desired tradeoff of noise and bandwidth. Adjust-
ment of these components will result in more or less ripple
due to auto-correction circuitry noise and will also affect
broadband noise. Filtering limits slew rate, settling time, and
output overload recovery time.
It is generally desirable to keep the resistance of R
O
relatively
low to avoid DC gain error created by the subsequent stage.
This may result in relatively high values for C
O
to produce the
desired filter response. The impedance of R
O
C
O
can be
scaled higher to produce smaller capacitor values if the load
impedance is very high.
Certain capacitor types greater than 0.1
μ
F may have dielec-
tric absorption effects that can significantly increase settling
time in high-accuracy applications (settling to 0.01%). Polypro-
pylene, polystyrene, and polycarbonate types are generally
good. Certain
high-K
ceramic types may produce slow
settling
tails.
Settling time to 0.1% is not generally affected
by high-K ceramic capacitors. Electrolytic types are not
recommended for C
2
and C
O
.
R
1
R
2
5
R
0
R
2
C
2
C
0
V
REF
= 10V to 5V
G = 2 (R
2
|| R
2
)/R
1
INA326
R
and R
are chosen to
create a small pedestal
voltage (e.g., 100mV).
Gain is determined by
the parallel combination
of R
2
and R
2
.
INA326
+5V
I
L
5
R
O
R
S
R
1
R
2
C
2
C
O
NOTE: Connection point
of V+ will include ( ) or
exclude ( ) quiescent
current in the measurement
as desired. Output pedestal
required for measurements
near zero (see Figure 5).
R
must be chosen
so that the input voltage
does not exceed 20mV
beyond the rail.
INA326
+5V
I
L
R
S
R
O
5
C
2
C
O
R
2
R
1
NOTE: Connection point of V
will include ( ) or
exclude ( ) quiescent current in the measurement
as desired. Output pedestal required for measurements
near zero (see Figure 5).
R
must be chosen so that
the input voltage does not
exceed 20mV beyond the rail.
2k
200k
200k
V
REF
R
O
5
C
O
C
2
V
REF
INA326
A/D
Converter
G = 2(200k
|| 200k
)/2k
= 100
INA326
+5V
NC
(1)
+15V
15V
OPA277
V
D
C
2
R
2
R
1
V
CM
5
(2)
NOTE: (1) NC denotes No Connection.
(2) Typical swing capability
20mV to +5V + 20mV.
相關PDF資料
PDF描述
INA326IDGKT INSTRUMENTATION AMPLIFIER|SINGLE|CMOS|TSSOP|8PIN|PLASTIC
INA327 Precision. Low Drift. CMOS Instrumentation Amplifier with Shutdown
INA327IDGSR INSTRUMENTATION AMPLIFIER|SINGLE|CMOS|TSSOP|10PIN|PLASTIC
INA327IDGST INSTRUMENTATION AMPLIFIER|SINGLE|CMOS|TSSOP|10PIN|PLASTIC
INA330 THERMISTOR SIGNAL AMPLIFIER FOR TEMPERATURE CONTROL
相關代理商/技術參數
參數描述
INA326IDGKT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INSTRUMENTATION AMPLIFIER|SINGLE|CMOS|TSSOP|8PIN|PLASTIC
INA327 制造商:TI 制造商全稱:Texas Instruments 功能描述:Precision, Rail-to-Rail I/O INSTRUMENTATION AMPLIFIER
INA327EA 制造商:Texas Instruments 功能描述:AMP INSTRUMENTATION VSSOP10 327
INA327EA/250 功能描述:儀表放大器 Precision Lo-Drift CMOS w/Shutdown RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比(最小值):88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk
INA327EA/250G4 功能描述:儀表放大器 Precision Lo-Drift CMOS w/Shutdown RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比(最小值):88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk