- 您現在的位置：買賣IC網 > PDF目錄360865 > INA2332AIPWT Precision Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | INA2332AIPWT |
| 元件分類： | 測量放大器 |
| 英文描述： | Precision Instrumentation Amplifier |
| 中文描述： | 精密儀表放大器 |
| 文件頁數： | 10/17頁 |
| 文件大?。?/td> | 292K |
| 代理商： | INA2332AIPWT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
INA332, INA2332
SBOS216A
10
www.ti.com
SETTING THE GAIN
The ratio of R
2
to R
1
, or the impedance between pins 1, 5,
and 6, determines the gain of the INA332. With an internally
set gain of 5, the INA332 can be programmed for gains
greater than 5 according to the following equation:
G = 5 + 5 (R
2
/R
1
)
The INA332 is designed to provide accurate gain, with gain
error less than 0.4%. Setting gain with matching TC resistors
will minimize gain drift. Errors from external resistors will add
directly to the error, and may become dominant error sources.
COMMON-MODE INPUT RANGE
The upper limit of the common-mode input range is set by the
common-mode input range of the second amplifier, A2, to
1.2V below positive supply. Under most conditions, the
amplifier operates beyond this point with reduced perfor-
mance. The lower limit of the input range is bounded by the
output swing of amplifier A1, and is a function of the refer-
ence voltage according to the following equation:
V
OA1
= 5/4 V
CM
–
1/4 V
REF
(See typical characteristic
“
Common-Mode Input Range vs
Reference Voltage
”
).
REFERENCE
The reference terminal defines the zero output voltage level.
In setting the reference voltage, the common mode input of
A3 should be considered according to the following equation:
V
OA2
= V
REF
+ 5 (V
IN
+
–
V
IN
–
)
For ensured operation, V
OA2
should be less than V
DD
–
1.2V.
The reference pin requires a low-impedance connection. As
little as 160
in series with the reference pin will degrade the
CMRR to 50dB. The reference pin may be used to compen-
sate for the offset voltage (see Offset Trimming section). The
reference voltage level also influences the common-mode
input range (see Common-Mode Input Range section).
INPUT BIAS CURRENT RETURN
With a high input impedance of 10
13
, the INA332 is ideal for
use with high-impedance sources. The input bias current of
less than 10pA makes the INA332 nearly independent of
input impedance and ideal for low-power applications.
For proper operation, a path must be provided for input bias
currents for both inputs. Without input bias current paths, the
inputs will
“
float
”
to a potential that exceeds common-mode
range and the input amplifier will saturate. Figure 3 shows
FIGURE 3. Providing an Input Common-Mode Path.
how bias current path can be provided in the cases of
microphone applications, thermistor applications, ground re-
turns, and dc-coupled resistive bridge applications.
When differential source impedance is low, the bias current
return path can be connected to one input. With higher
source impedance, two equal resistors will provide a bal-
anced input. The advantages are lower input offset voltage
due to bias current flowing through the source impedance
and better high-frequency gain.
47k
Microphone,
Hydrophone,
etc.
Center-tap
provides bias
current return
Bridge resistance
provides bias
current return
Transformer
Bridge
Amplifier
Bridge
Sensor
V
B(1)
V
B(1)
V
EX
NOTE: (1) V
is bias voltage within
common-mode range, dependent
on REF.
INA332
5
3
2
8
7
6
4
1
V+
Shutdown
V
IN
–
V
–
V
IN
+
REF
INA332
5
3
2
8
7
6
4
1
V+
Shutdown
V
IN
–
V
–
V
IN
+
REF
INA332
5
3
2
8
7
6
4
1
V+
Shutdown
V
IN
–
V
–
V
IN
+
REF
V
OUT
RG
V
OUT
RG
V
OUT
RG
相關PDF資料 |
PDF描述 |
|---|---|
| INA270_07 | Voltage Output, Unidirectional Measurement Current-Shunt Monitor |
| INA270AIDG4 | Voltage Output, Unidirectional Measurement Current-Shunt Monitor |
| INA270AIDRG4 | Voltage Output, Unidirectional Measurement Current-Shunt Monitor |
| INA271AIDG4 | Voltage Output, Unidirectional Measurement Current-Shunt Monitor |
| INA271AIDRG4 | Voltage Output, Unidirectional Measurement Current-Shunt Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA2332AIPWTG4 | 功能描述:儀表放大器 Lo-Pwr Single Sply CMOS RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA233AIDGST | 功能描述:CURRENT SHUNT POWER MONITOR WITH 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
| INA233EVM | 功能描述:EVAIL MOD 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
| INA240A1PW | 功能描述:WIDE CM BI-DIR CURRENT SHUNT MON 制造商:texas instruments 系列:- 包裝:管件 零件狀態:在售 放大器類型:電流檢測 電路數:1 輸出類型:- 壓擺率:2 V/μs -3db 帶寬:400kHz 電流 - 輸入偏置:90μA 電壓 - 輸入失調:5μV 電流 - 電源:1.8mA 電壓 - 電源，單/雙（±）:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:8-TSSOP 標準包裝:150 |
| INA240A1PWR | 功能描述:IC AMP CURRENT SENSE 8-TSSOP 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:在售 放大器類型:電流檢測 電路數:1 輸出類型:- 壓擺率:2 V/μs -3db 帶寬:400kHz 電流 - 輸入偏置:90μA 電壓 - 輸入失調:5μV 電流 - 電源:1.8mA 電壓 - 電源，單/雙（±）:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:8-TSSOP 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。