參數資料
型號: INA2141UA
元件分類: 測量放大器
英文描述: Dual, Low Power, G = 10, 100 INSTRUMENTATION AMPLIFIER
中文描述: 雙通道,低功耗G \u003d 10,100款儀表放大器
文件頁數: 10/10頁
文件大?。?/td> 243K
代理商: INA2141UA
INA2141
10
INPUT PROTECTION
The inputs of the INA2141 are individually protected for
voltages up to
±
40V. For example, a condition of –40V on
one input and +40V on the other input will not cause
damage. Internal circuitry on each input provides low series
impedance under normal signal conditions. To provide
equivalent protection, series input resistors would contribute
excessive noise. If the input is overloaded, the protection
circuitry limits the input current to a safe value of approxi-
mately 1.5 to 5mA. The typical performance curve “Input
Bias Current vs Common-Mode Input Voltage” shows this
input current limit behavior. The inputs are protected even if
the power supplies are disconnected or turned off.
CHANNEL CROSSTALK
The two channels of the INA2141 are completely indepen-
dent, including all bias circuitry. At DC and low frequency
there is virtually no signal coupling between channels.
Crosstalk increases with frequency and is dependent on
circuit gain, source impedance and signal characteristics.
As source impedance increases, careful circuit layout will
help achieve lowest channel crosstalk. Most crossstalk is
produced by capacitive coupling of signals from one channel
to the input section of the other channel. To minimize
coupling, separate the input traces as far as practical from
any signals associated with the opposite channel. A grounded
guard trace surrounding the inputs helps reduce stray cou-
pling between channels. Run the differential inputs of each
channel parallel to each other or directly adjacent on top and
bottom side of a circuit board. Stray coupling then tends to
produce a common-mode signal which is rejected by the
IA’s input.
FIGURE 6. ECG Amplifier With Right-Leg Drive.
FIGURE 4. Two-Axis Bridge Amplifier.
FIGURE 5. Sum of Differences Amplifier.
X-axis
V
O
Y-axis
V
O
X-axis
Y-axis
V
EX
V
EX
INA2141
1/2
INA2141
1/2
V
O
= 10 (V
2
– V
1
) + 10 (V
4
– V
3
)
V
1
V
2
Ref
V
3
V
4
Ref
INA2141
1/2
INA2141
1/2
INA2141
1/2
V
O
LA
RL
RA
10k
Ref
G = 10
20k
20k
V
G
1/4
OPA4131
390k
390k
1/4
OPA4131
OPA4131
1/4
OPA4131
1/4
相關PDF資料
PDF描述
INA2143U High-Speed, Precision, G = 10 or G = 0.1 DIFFERENCE AMPLIFIERS
INA143 High-Speed, Precision, G = 10 or G = 0.1 DIFFERENCE AMPLIFIERS
INA143U High-Speed, Precision, G = 10 or G = 0.1 DIFFERENCE AMPLIFIERS
INA143UA High-Speed, Precision, G = 10 or G = 0.1 DIFFERENCE AMPLIFIERS
INA2143UA High-Speed, Precision, G = 10 or G = 0.1 DIFFERENCE AMPLIFIERS
相關代理商/技術參數
參數描述
INA2141UA 制造商:Texas Instruments 功能描述:AMP INST DUAL SMD SOIC16 2121
INA2141UA/1K 功能描述:差分放大器 Dual Low Power G = 10 100 RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比(最小值):- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel
INA2141UA/1KE4 功能描述:差分放大器 Dual Low Power G = 10 100 RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比(最小值):- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel
INA2141UAE4 功能描述:差分放大器 Dual Low Power G = 10 100 RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比(最小值):- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel
INA2141UE4 功能描述:差分放大器 Dual Low Power RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比(最小值):- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel