- 您現在的位置：買賣IC網 > PDF目錄10618 > IL3585E (NVE Corp/Isolation Products)TXRX ISO PROFIBUS RS485 16SOIC PDF資料下載
參數資料
| 型號： | IL3585E |
| 廠商： | NVE Corp/Isolation Products |
| 文件頁數： | 3/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | TXRX ISO PROFIBUS RS485 16SOIC |
| 產品培訓模塊： | IsoLoop® Isolator |
| 產品目錄繪圖： | IL3585E Circuit |
| 特色產品： | Wide-Body SOIC-16 Isolators |
| 標準包裝： | 50 |
| 系列： | IsoLoop® |
| 類型： | 收發器，隔離式 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS485 |
| 電源電壓： | 3.3V，5V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 2771 (CN2011-ZH PDF) |
| 其它名稱： | 390-1101-5 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
IL3585
11
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
NVE Corporation
Fail-Safe Operation
“Fail-safe operation” is defined here as the forcing of a logic high state on the “R” output in response to an open-circuit condition between the
“A” and “B” lines of the bus, or when no drivers are active on the bus.
Proper biasing can ensure fail-safe operation, that is a known state when there are no active drivers on the bus. IL3000-Series Isolated
Transceivers include internal pull-up and pull-down resistors of approximately 30 k in the receiver section (RFS-INT; see figure below). These
internal resistors are designed to ensure failsafe operation but only if there are no termination resistors. The entire VDD will appear between inputs
“A” and “B” if there is no loading and no termination resistors, and there will be more than the required 200 mV with up to four RS-485 worst-
case Unit Loads of 12 k. Many designs operating below 1 Mbps or less than 1,000 feet are unterminated. Termination resistors may not be
necessary for very low data rates and very short cable runs because reflections have time to settle before data sampling, which occurs at the
middle of the bit interval.
In busses with low-impedance termination resistors however, the differential voltage across the conductor pair will be close to zero with no active
drivers. In this case the state of the bus is indeterminate, and the idle bus will be susceptible to noise. For example, with 120 termination
resistors (RT) on each end of the cable, and four Unit Loads (12 k each), without external fail-safe biasing resistors the internal pull-up and pull-
down resistors will produce a voltage between inputs “A” and “B” of only about 5 mV. This is not nearly enough to ensure a known state.
External fail-safe biasing resistors (RFS-EXT) at one end of the bus can ensure fail-safe operation with a terminated bus. Resistors should be
selected so that under worst-case power supply and resistor tolerances there is at least 200 mV across the conductor pair with no active drivers to
meet the input sensitivity specification of the RS-485 standard.
Using the same value for pull-up and pull-down biasing resistors maintains balance for positive- and negative going transitions. Lower-value
resistors increase inactive noise immunity at the expense of quiescent power consumption. Note that each Unit Load on the bus adds a worst-case
loading of 12 k across the conductor pair, and 32 Unit Loads add 375 worst-case loading. The more loads on the bus, the lower the required
values of the biasing resistors.
In the example with two 120 termination resistors and four Unit Loads, 560 external biasing resistors provide more than 200 mV between
“A” and “B” with adequate margin for power supply variations and resistor tolerances. This ensures a known state when there are no active
drivers. Other illustrative examples are shown in the table below:
Fail-Safe Biasing
R
B
V
DD
30K
GND
A
5 V
R
FS-EXT
R
T
R
T
R
FS-EXT
R
FS-INT
R
FS-INT
Fail-Safe
RT
Loading
Operation?
None
Four unit loads (12 k ea.)
238 mV
Yes
120
Four unit loads (12 k ea.)
5 mV
No
560
120
Four unit loads (12 k ea.)
254 mV
Yes
510
120
32 unit loads (12 k ea.)
247 mV
Yes
Nominal VA-B
(inactive)
RFS-EXT
Internal Only
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2WM-IW-F2 | CONVERTER MOD DC/DC 10V 100W |
| VE-BWK-MX-F4 | CONVERTER MOD DC/DC 40V 75W |
| VI-2WL-IW-F4 | CONVERTER MOD DC/DC 28V 100W |
| VE-J02-MY-F1 | CONVERTER MOD DC/DC 15V 50W |
| VI-2WL-IW-F3 | CONVERTER MOD DC/DC 28V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IL3585ETR13 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PROFIBUS Compatible Isolated RS485 Interface |
| IL3585TR13 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PROFIBUS Compatible Isolated RS485 Interface |
| IL3585VE | 功能描述:RS422, RS485 Digital Isolator 6000Vrms 3 Channel 40Mbps 30kV/μs CMTI 16-SOIC (0.154", 3.90mm Width) 制造商:nve corp/isolation products 系列:IsoLoop? 包裝:管件 零件狀態:有效 技術:GMR（大型磁阻傳感） 類型:RS422，RS485 隔離式電源:無 通道數:3 輸入 - 輸入側 1/輸入側 2:2/1 通道類型:單向 電壓 - 隔離:6000Vrms 共模瞬態抗擾度（最小值）:30kV/μs 數據速率:40Mbps 傳播延遲 tpLH / tpHL（最大值）:35ns，35ns 脈寬失真（最大）:- 上升/下降時間（典型值）:- 電壓 - 電源:3 V ~ 5.5 V，4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:16-SOIC 標準包裝:50 |
| IL358C-1663 | 制造商:Siemens 功能描述:HIGH PERFORMANCE LINEAR OPTOCOUPLER FOR OPTICAL DAA IN TELECOMMUNICATIONS |
| IL358D | 制造商:INTEGRAL 制造商全稱:INTEGRAL 功能描述:Low Power Dual Operational Amplifier |
發布緊急采購，3分鐘左右您將得到回復。