參數資料
型號: IL3285
廠商: NVE Corp/Isolation Products
文件頁數: 18/18頁
文件大?。?/td> 0K
描述: IC TXRX RS485 ISOLATED 16SOICW
產品培訓模塊: IsoLoop® Isolator
標準包裝: 50
系列: IsoLoop®
類型: 收發器,隔離式
驅動器/接收器數: 1/1
規程: RS485
電源電壓: 3.3V,5V
安裝類型: 表面貼裝
封裝/外殼: 16-SOIC(0.295",7.50mm 寬)
供應商設備封裝: *
包裝: 管件
其它名稱: 390-1034-5
IL3285/IL3222
9
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
www.isoloop.com
iso-info@nve.com
NVE Corporation
Cabling, Data Rate and Terminations
Cabling
Use twisted-pair cable. The cable can be unshielded if it is short (less than 10 meters) and the data rate is slow (less than
100 Kbps). Otherwise, use screened cable with the shield tied to earth ground at one end only. Do not tie the shield to digital
ground. The other end of the shield may be tied to earth ground through an RC network. This prevents a DC ground loop in the
shield. Shielded cable minimizes EMI emissions and external noise coupling to the bus.
Data Rate
The longer the cable, the slower the data rate. The RS-485 bus can transmit ground over 4,000 feet (1,200 meters) or at 10 Mbps,
but not both at the same time. Transducer and cable characteristics combine to act as a filter with the general response shown in
Figure 3. Other parameters such as acceptable jitter affect the final cable length versus data rate tradeoff. Less jitter means better
signal quality but shorter cable lengths or slower data rates. Figure 4 shows a generally accepted 30% jitter and a corresponding
data rate versus cable length.
Figure 3. Cable Length vs. Data Rate (30% jitter).
Terminations
Transmission lines should be terminated to avoid reflections that cause data errors. In RS-485 systems both ends of the bus, not
every node, should be terminated. In RS-422 systems only the receiver end should be terminated.
100
Unterminated
Parallel
Proper termination is imperative when using IL3285 and IL3222 to minimize reflections. Unterminated lines are only suitable for
very low data rates and very short cable runs, otherwise line reflections cause problems. Parallel terminations are the most popular.
They allow high data rates and excellent signal quality.
Occasionally in noisy environments, fast pulses or noise appearing on the bus lines cause errors. One way of alleviating such errors
without adding circuit delays is to place a series resistor in the bus line. Depending on the power supply, the resistor should be
between 300 (3 V supply) and 500 (5 V supply).
1000
100
40
4000
100
1K
10K
100K
1M
10M
Data Rate (bps)
Cable Length (feet)
相關PDF資料
PDF描述
LTC1747CFW#PBF IC ADC 12BIT 80MSPS 48-TSSOP
MAX3443EASA+T IC TXRX RS-485 8-SOIC
MS27467E21B16SB CONN PLUG 16POS STRAIGHT W/SCKT
VI-2N1-IU-F2 CONVERTER MOD DC/DC 12V 200W
VI-BTJ-MW-F2 CONVERTER MOD DC/DC 36V 100W
相關代理商/技術參數
參數描述
IL3285-3E 功能描述:TXRX ISO BUS 5MBPS RS485 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:IsoLoop® 標準包裝:1,240 系列:GD 類型:收發器 驅動器/接收器數:3/5 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:20-DIP(0.300",7.62mm) 供應商設備封裝:20-PDIP 包裝:管件
IL3285E 功能描述:TXRX ISO BUS 1MBS RS485 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:IsoLoop® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422,RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-PDIP 包裝:管件 產品目錄頁面:1402 (CN2011-ZH PDF)
IL3285ETR13 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Fractional Load RS485 and RS422 Transceivers
IL3285TR13 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Fractional Load RS485 and RS422 Transceivers
IL329 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:OPTICALLY COUPLED TELECOM SWITCH