
      6.42
IDT70121/IDT70125
High-Speed 2K x 9 Dual-Port Static RAM with Busy & Interrupt                                       Industrial and Commercial Temperature Ranges
AC Elec tric al Charac teristic s Over the
Operating Temperature and S upply Voltage Range
(4)
 APRIL 05, 2006
NOTES:
1. Transition is measured 0mV fromLow or High-impedance voltage with Output Test Load (Figure 2).
2. This parameter guaranteed by device characterization, but is not production tested.
3. For MASTER/SLAVE combination, t
WC
 = t
BAA
 + t
WP,
 since R/W 
= V
IL
 must occur after t
BAA
 .
4. 'X' in part numbers indicates power rating (S or L).
5. The specified t
DH 
 must be met by the device supplying write date to the RAMunder all operating conditions.
Although t
DH 
and
t
OW
values will vary over voltage  and temperature. The actual t
DH 
will always be smaller than the actual t
OW.
6. If 
OE
 is LOW during a R/
W
 controlled write cycle, the write pulse width must be the larger of t
WP
 or (t
WZ
 + t
DW
) to allow the I/O drivers to turn off data to be
placed on the bus for the required t
DW
. If 
OE
 is HIGH during a R/
W
 controlled write cycle, this requirement does not apply and the write pulse can be as short
as the specified t
WP
.
Symbol
Parameter
70121X25
70125X25
Com'l Only
70121X35
70125X35
Com'l
& Ind
Unit
Min.
Max.
Mn.
Max.
WRITE CYCLE
t
 WC
Write Cycle Time
 (4)
25
____
35
____
ns
t
 EW
Chip Enable to End-of-Write
20
____
30
____
ns
t
 AW
Address Valid to End-of-Write
20
____
30
____
ns
t
 AS
Address Set-up Time
0
____
0
____
ns
t
 WP
Write Pulse Width
(6)
20
____
30
____
ns
t
 WR
Write Recovery Time
0
____
0
____
ns
t
 DW
Data Valid to End-of-Write
12
____
20
____
ns
t
 HZ
Output High-Z Time
(1,2,3)
____
10
____
15
ns
t
 DH
Data Hold Time
(5)
0
____
0
____
ns
t
 WZ
Write Enable to Output in High-Z
(1,3)
____
10
____
15
ns
t
 OW
Output Active fromEnd-of-Write
(1,2,3,5)
0
____
0
____
ns
2654 tbl 10a
Symbol
Parameter
70121X45
70125X45
Com'l Only
70121X55
70125X55
Com'l Only
Unit
Min.
Max.
Mn.
Max.
WRITE CYCLE
t
 WC
Write Cycle Time
(4)
45
____
55
____
ns
t
 EW
Chip Enable to End-of-Write
35
____
40
____
ns
t
 AW
Address Valid to End-of-Write
35
____
____
ns
t
 AS
Address Set-up Time
0
____
0
____
ns
t
 WP
Write Pulse Width
(6)
35
____
40
____
ns
t
 WR
Write Recovery Time
0
____
0
____
ns
t
 DW
Data Valid to End-of-Write
20
____
20
____
ns
t
 HZ
Output High-Z Time
(1,2,3)
____
20
____
30
ns
t
 DH
Data Hold Time
(5)
0
____
0
____
ns
t
 WZ
Write Enable to Output in High-Z
(1,3)
____
20
____
30
ns
t
 OW
Output Active fromEnd-of-Write
(1,2,3,5)
0
____
0
____
ns
2654 tbl 10b