參數資料
型號： ICX419AKB
英文描述： CCD IMAGE SENSOR Diag. 8mm (Type 1/2) CCD Image Sensor for PAL Color Video Cameras (20 pages 196K Rev. E01911)
中文描述： CCD圖像傳感器診斷工具。 8毫米（類型1 / 2）防治荒漠化公約對于PAL彩色視頻攝像機圖像傳感器（20頁196K牧師E01911）
文件頁數： 30/32頁
文件大?。?/td> 441K
代理商： ICX419AKB
– 30 –
ICX411AQ
50N
50N
1.2Nm
Notes on Handling
1) Static charge prevention
CCD image sensors are easily damaged by static discharge. Before handling be sure to take the following
protective measures.
a) Either handle bare handed or use non-chargeable gloves, clothes or material.
Also use conductive shoes.
b) When handling directly use an earth band.
c) Install a conductive mat on the floor or working table to prevent the generation of static electricity.
d) Ionized air is recommended for discharge when handling CCD image sensors.
e) For the shipment of mounted substrates, use boxes treated for the prevention of static charges.
2) Soldering
a) Make sure the package temperature does not exceed 80°C.
b) Solder dipping in a mounting furnace causes damage to the glass and other defects. Use a 30W
soldering iron with a ground wire and solder each pin in less than 2 seconds. For repairs and remount,
cool sufficiently.
c) To dismount an image sensor, do not use a solder suction equipment. When using an electric desoldering
tool, use a thermal controller of the zero-cross On/Off type and connect it to ground.
3) Dust and dirt protection
Image sensors are packed and delivered by taking care of protecting its glass plates from harmful dust and
dirt. Clean glass plates with the following operations as required, and use them.
a) Perform all assembly operations in a clean room (class 1000 or less).
b) Do not either touch glass plates by hand or have any object come in contact with glass surfaces. Should
dirt stick to a glass surface, blow it off with an air blower. (For dirt stuck through static electricity ionized
air is recommended.)
c) Clean with a cotton bud and ethyl alcohol if grease stained. Be careful not to scratch the glass.
d) Keep in a case to protect from dust and dirt. To prevent dew condensation, preheat or precool when
moving to a room with great temperature differences.
e) When a protective tape is applied before shipping, just before use remove the tape applied for
electrostatic protection. Do not reuse the tape.
4) Installing (attaching)
a) Remain within the following limits when applying a static load to the package. Do not apply any load
more than 0.7mm inside the outer perimeter of the glass portion, and do not apply any load or impact to
limited portions. (This may cause cracks in the package.)
b) If a load is applied to the entire surface by a hard component, bending stress may be generated and the
package may fracture, etc., depending on the flatness of the bottom of the package. Therefore, for
installation, use either an elastic load, such as a spring plate, or an adhesive.
相關PDF資料
PDF描述
ICX419ALB Diagonal 8mm(Type 1/2) CCD Image Sensor forCCIR B/W Video Cameras
ICX428AKL Diagonal 8mm(Type 1/2) CCD Image Sensorfor NTSC Color Video Cameras
ICX429AKL Diagonal 8mm(Type 1/2) CCD Image Sensorfor PAL Color Video Cameras
ICXO58CL AREA CCD IMAGE ARRAY
ID1014 White Bronze
相關代理商/技術參數
參數描述
ICX419AKL 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 8mm (Type 1/2) CCD Image Sensor for PAL Color Video Cameras
ICX419ALB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Diagonal 8mm(Type 1/2) CCD Image Sensor forCCIR B/W Video Cameras
ICX419ALL 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 8mm (Type 1/2) CCD Image Sensor for CCIR B/W Video Cameras
ICX422 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 11mm (Type 2/3) CCD Image Sensor for EIA B/W Video Cameras
ICX422AL 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 11mm (Type 2/3) CCD Image Sensor for EIA B/W Video Cameras
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*