參數資料
型號： ICSSSTUBF32866A
英文描述： 25-Bit Configurable Registered Buffer for DDR2
中文描述： 25位可配置的注冊緩沖DDR2內存
文件頁數： 3/28頁
文件大?。?/td> 308K
代理商： ICSSSTUBF32866A
3
ICSSSTUBF32866A
Advance Information
1240—07/17/06
General Description
This 25-bit 1:1 or 14-bit 1:2 configurable registered buffer is designed for 1.7-V to 1.9-V VDD operation.
All clock and data inputs are compatible with the JEDEC standard for SSTL_18. The control inputs are LVCMOS. All
outputs are 1.8-V CMOS drivers that have been optimized to drive the DDR-II DIMM load.
ICSSSTUBF32866A
operates from a differential clock (CK and CK). Data are registered at the crossing of CK going high, and CK going
low.
The C0 input controls the pinout configuration of the 1:2 pinout from A configuration (when low) to B configuration (when
high). The C1 input controls the pinout configuration from 25-bit 1:1 (when low) to 14-bit 1:2 (when high).
A - Pair Configuration (CO
1
= 0, CI
1
= 1 and CO
2
= 0, CI
2
= 1)
Parity that arrives one cycle after the data input to which it applies is checked on the PAR_IN of the first register.
The second register produces to PPO and QERR signals. The QERR of the first register is left floating. The valid
error information is latched on the QERR output of the second register. If an error occurs QERR is latched low for
two cycles or until Reset is low.
B - Single Configuration (CO = 0, C1 = 0)
The device supports low-power standby operation. When the reset input (RST) is low, the differential input receivers
are disabled, and undriven (floating) data, clock and reference voltage (VREF) inputs are allowed. In addition, when
RST is low all registers are reset, and all outputs are forced low. The LVCMOS RST and Cn inputs must always be
held at a valid logic high or low level. To ensure defined outputs from the register before a stable clock has been supplied,
RST must be held in the low state during power up.
In the DDR-II RDIMM application, RST is specified to be completely asynchronous with respect to CK and CK.
Therefore, no timing relationship can be guaranteed between the two. When entering reset, the register will be cleared
and the outputs will be driven low quickly, relative to the time to disable the differential input receivers. However, when
coming out of reset, the register will become active quickly, relative to the time to enable the differential input receivers.
As long as the data inputs are low, and the clock is stable during the time from the low-to-high transition of RST until
the input receivers are fully enabled, the design of the
ICSSSTUBF32866A
must ensure that the outputs will remain
low, thus ensuring no glitches on the output.
The device monitors both DCS and CSR inputs and will gate the Qn outputs from changing states when both DCS and
CSR inputs are high. If either DCS or CSR input is low, the Qn outputs will function normally. The RST input has priority
over the DCS and CSR control and will force the outputs low. If the DCS-control functionality is not desired, then the
CSR input can be hardwired to ground, in which case, the setup-time requirement for DCS would be the same as for
the other D data inputs. Package options include 96-ball LFBGA (MO-205CC).
Parity and Standby Functionality Truth Table
Inputs
Rst
DCS
CSR
CK
CK
Sum of Inputs = H
(D1 - D25)
Even
Odd
Even
Odd
Even
Odd
X
X
PAR_IN
PPO
QERR
H
H
H
H
H
H
H
H
L
L
L
L
H
H
H
X
X
X
X
X
L
L
H
X
↑
↑
↑
↑
↑
↑
↑
↓
↓
↓
↓
↓
↓
↓
L
L
H
H
L
H
X
X
L
H
H
L
L
H
H
L
L
H
H
L
PPO
0
PPO
0
QERR
0
QERR
0
L or H
L or H
L
X or
Floating
X or
Floating
X or
Floating
X or
Floating
X or Floating
X or
Floating
L
H
3. PAR_IN arrives two clock cycles after the data to which it applies when CO = 1.
4. Assume QERR is high at the CK
↑
and CK
↓
crossing. If QERR is low it stays latched low for two
clock cycles on until Rst is low.
Outputs
1. CO = 0 and CI = 0, Data inputs are D2, D3, D5, D6, D8 - D25.
CO = 0 and CI = 1, Data inputs are D2, D3, D5, D6, D8 - D14
CO = 1 and CI = I, Data inputs are D1 - D6, D8 - D10, D12, D13
2. PAR_IN arrives one clock cycle after the data to which it applies when CO = 0.
相關PDF資料
PDF描述
ICSSSTUBF32866Az(LF)T 25-Bit Configurable Registered Buffer for DDR2
ICSSSTUF32864A 25-Bit Configurable Registered Buffer for DDR2
ICSSSTUF32864AYHLF-T 25-Bit Configurable Registered Buffer for DDR2
ICSSSTV16857CG-T DDR 14-Bit Registered Buffer
ICSSSTV16857yG-T DDR 14-Bit Registered Buffer
相關代理商/技術參數
參數描述
ICSSSTUBF32866AZ(LF)T 制造商:ICS 制造商全稱:ICS 功能描述:25-Bit Configurable Registered Buffer for DDR2
ICSSSTUF32864A 制造商:ICS 制造商全稱:ICS 功能描述:25-Bit Configurable Registered Buffer for DDR2
ICSSSTUF32864AYHLF-T 制造商:ICS 制造商全稱:ICS 功能描述:25-Bit Configurable Registered Buffer for DDR2
ICSSSTV16857 制造商:ICS 制造商全稱:ICS 功能描述:DDR 14-Bit Registered Buffer
ICSSSTV16857CG-T 制造商:ICS 制造商全稱:ICS 功能描述:DDR 14-Bit Registered Buffer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*