- 您現在的位置：買賣IC網 > PDF目錄360785 > ICS950202 Programmable Timing Control HubTM for P4TM PDF資料下載
參數資料
| 型號： | ICS950202 |
| 英文描述： | Programmable Timing Control HubTM for P4TM |
| 中文描述： | 可編程定時控制HubTM的P4TM |
| 文件頁數： | 16/19頁 |
| 文件大?。?/td> | 162K |
| 代理商： | ICS950202 |
16
Integrated
Circuit
Systems, Inc.
ICS950202
0461L—05/28/03
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) serve as dual
signal functions to the device. During initial power-up, they
act as input pins. The logic level (voltage) that is present on
these pins at this time is read and stored into a 5-bit internal
data latch. At the end of Power-On reset, (see AC
characteristics for timing values), the device changes the
mode of operations for these pins to an output function. In this
mode the pins produce the specified buffered clocks to
external loads.
To program (load) the internal configuration register for these
pins, a resistor is connected to either the VDD (logic 1) power
supply or the GND (logic 0) voltage potential. A 10 Kilohm
(10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
8.2K
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the series
termination resistor to minimize the current loop area. It is
more important to locate the series termination resistor
close to the driver than the programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS950208 | Programmable Timing Control Hub for P4 |
| ICS950211 | Programmable Timing Control Hub for P4 |
| ICS950211YFLF-T | Programmable Timing Control Hub for P4 |
| ICS950211YGLF-T | Programmable Timing Control Hub for P4 |
| ICS950220 | Programmable Timing Control Hub⑩ for P4⑩ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS950202BF | 制造商:Ics 功能描述:PROGRAMMABLE TIMING CONTROL HUB FOR P4 |
| ICS950208 | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for P4 |
| ICS950211 | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for P4 |
| ICS950211BF | 功能描述:IC TIMING CTRL HUB P4 56-SSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:TCH™ 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| ICS950211BFLF | 功能描述:IC TIMING CTRL HUB P4 56-SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:TCH™ 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。