- 您現在的位置：買賣IC網 > PDF目錄360772 > ICS8442 Hex schmitt-trigger inverters 14-SOIC 0 to 70 PDF資料下載
參數資料
| 型號： | ICS8442 |
| 英文描述： | Hex schmitt-trigger inverters 14-SOIC 0 to 70 |
| 中文描述： | 700MHz的，晶體振蕩器至差分LVDS的頻率合成器 |
| 文件頁數： | 11/15頁 |
| 文件大?。?/td> | 284K |
| 代理商： | ICS8442 |
8442AY
www.icst.com/products/hiperclocks.html
REV. C JULY 8, 2004
11
Integrated
Circuit
Systems, Inc.
ICS8442
700MH
Z
, C
RYSTAL
O
SCILLATOR
-
TO
-D
IFFERENTIAL
LVDS F
REQUENCY
S
YNTHESIZER
The following component footprints are used in this layout
example: All the resistors and capacitors are size 0603.
P
OWER
AND
G
ROUNDING
Place the decoupling capacitors C14 and C15 as close as pos-
sible to the power pins. If space allows, placing the decoupling
capacitor at the component side is preferred. This can reduce
unwanted inductance between the decoupling capacitor and the
power pin generated by the via.
Maximize the pad size of the power (ground) at the decoupling
capacitor. Maximize the number of vias between power (ground)
and the pads. This can reduce the inductance between the power
(ground) plane and the component power (ground) pins.
If V
shares the same power supply with V
, insert the RC
filter R7, C11, and C16 in between. Place this RC filter as close
to the V
DDA
as possible.
C
LOCK
T
RACES
AND
T
ERMINATION
The component placements, locations and orientations should
be arranged to achieve the best clock signal quality. Poor clock
signal quality can degrade the system performance or cause
system failure. In the synchronous high-speed digital system,
the clock signal is less tolerable to poor signal quality than other
signals. Any ringing on the rising or falling edge or excessive ring
back can cause system failure. The trace shape and the trace
delay might be restricted by the available space on the board and
the component location. While routing the traces, the clock signal
traces should be routed first and should be locked prior to routing
other signal traces.
The traces with 50
transmission lines TL1 and TL2 at
FOUT and nFOUT should have equal delay and run ad-
jacent to each other. Avoid sharp angles on the clock trace.
Sharp angle turns cause the characteristic impedance to
change on the transmission lines.
Keep the clock trace on same layer. Whenever possible,
avoid any vias on the clock traces. Any via on the trace
can affect the trace characteristic impedance and hence
degrade signal quality.
To prevent cross talk, avoid routing other signal traces in
parallel with the clock traces. If running parallel traces is
unavoidable, allow more space between the clock trace
and the other signal trace.
Make sure no other signal trace is routed between the
clock trace pair.
The matching termination resistors R1 and R2 should be located
as close to the receiver input pins as possible. Other termination
scheme can also be used but is not shown in this example.
C
RYSTAL
The crystal X1 should be located as close as possible to the pins
24 (XTAL1) and 25 (XTAL2). The trace length between the X1
and U1 should be kept to a minimum to avoid unwanted parasitic
inductance and capacitance. Other signal traces should not be
routed near the crystal traces.
F
IGURE
5B. PCB B
OARD
L
AYOUT
FOR
ICS8442
VDD
TL1
C15
C14
R1
Same requirement fo
VDDA
Close to the input
pins of the
receiver
R7
X1
C2
For FOUT0/n FOUT0
output TL1, TL1N are
50 Ohm traces and
equal length
VIA
GND
T
T
PIN 1
U1
C1
TL1N
C11
C16
相關PDF資料 |
PDF描述 |
|---|---|
| ICS8442AY | Hex schmitt-trigger inverters 14-SOIC 0 to 70 |
| ICS8442AYLF | 700MHZ, CRYSTAL OSCILLATOR-TO-DIFFERENTIAL LVDS FREQUENCY SYNTHESIZER |
| ICS8501 | Low Skew 1-to-16 Differential Current Mode Fanout Buffer |
| ICS8501BY | Low Skew 1-to-16 Differential Current Mode Fanout Buffer |
| ICS8501BYT | Low Skew 1-to-16 Differential Current Mode Fanout Buffer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS844201BG-45LF | 功能描述:IC CLK GENERATOR 25MHZ 8TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:HiPerClockS™, FemtoClock™, PCI Express® (PCIe) 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| ICS844201BG-45LFT | 功能描述:IC CLK GENERATOR 25MHZ 8TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:HiPerClockS™, FemtoClock™, PCI Express® (PCIe) 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| ICS844201BGI-45LF | 功能描述:IC CLK GENERATOR 25MHZ 8TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:HiPerClockS™, FemtoClock™, PCI Express® (PCIe) 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| ICS844201BGI-45LFT | 功能描述:IC CLK GENERATOR 25MHZ 8TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:HiPerClockS™, FemtoClock™, PCI Express® (PCIe) 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| ICS844202AK-245LF | 功能描述:IC CLOCK GEN SRL SCSI 32-VFQFPN RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:HiPerClockS™, PCI Express® (PCIe) 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。