- 您現在的位置：買賣IC網 > PDF目錄9030 > ICS671M-03ILFT (IDT, Integrated Device Technology Inc)IC BUFFER/MULT ZD 16-SOIC PDF資料下載
參數資料
| 型號： | ICS671M-03ILFT |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 3/9頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC BUFFER/MULT ZD 16-SOIC |
| 標準包裝： | 2,500 |
| 類型： | 扇出緩沖器（分配），零延遲緩沖 |
| PLL： | 帶旁路 |
| 輸入： | 時鐘 |
| 輸出： | CMOS |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:8 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 133MHz |
| 除法器/乘法器： | 無/無 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 671M-03ILFT |
ICS671-03
3.3 VOLT ZERO DELAY, LOW SKEW BUFFER
ZDB AND MULTIPLIER
IDT 3.3 VOLT ZERO DELAY, LOW SKEW BUFFER
3
ICS671-03
REV D 051310
External Components
The ICS671-03 requires a minimum number of external
components for proper operation. Decoupling capacitors of
0.01F should be connected between VDD and GND on
pins 4 and 5, and VDD and GND on pins 13 and 12, as close
to the device as possible. A series termination resistor of 33
may be used close to each clock output pin to reduce
reflections.
Decoupling Capacitor
A decoupling capacitor of 0.01F must be connected
between VDD and GND, as close to these pins as possible.
For optimum device performance, the decoupling capacitor
should be mounted on the component side of the PCB.
Avoid the use of vias in the decoupling circuit.
Series Termination Resistor
When the PCB trace between the clock outputs and the
loads are over 1 inch, series termination should be used. To
series terminate a 50
trace (a commonly used trace
impedance) place a 33
resistor in series with the clock line,
as close to the clock output pin as possible. The nominal
impedance of the clock output is 20
.
PCB Layout Recommendations
For optimum device performance and lowest output phase
noise, the following guidelines should be observed.
1) The 0.01F decoupling capacitor should be mounted on
the component side of the board as close to the VDD pin as
possible. No vias should be used between decoupling
capacitor and VDD pin. The PCB trace to VDD pin should
be kept as short as possible, as should the PCB trace to the
ground via.
2) The external crystal should be mounted just next to the
device with short traces. The X1 and X2 traces should not
be routed next to each other with minimum spaces, instead
they should be separated and away from other traces.
3) To minimize EMI, the 33
series termination resistor (if
needed) should be placed close to the clock output.
4) An optimum layout is one with all components on the
same side of the board, minimizing vias through other signal
layers. Other signal traces should be routed away from the
ICS671-03. This includes signal traces just underneath the
device, or on layers adjacent to the ground plane layer used
by the device.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-234-MW-F3 | CONVERTER MOD DC/DC 48V 100W |
| IDT23S09T-1DCG | IC CLK BUFF ZD SPRD SPECT 16SOIC |
| VE-234-MW-F2 | CONVERTER MOD DC/DC 48V 100W |
| IDT23S09E-1DCG | IC CLK BUFF ZD 16SOIC |
| MK2732-06GLFTR | IC VCXO/MULTIPLIER 16-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS671M-03IT | 功能描述:IC BUFFER/MULT ZD 16-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 產品變化通告:Product Discontinuation 04/May/2011 標準包裝:96 系列:- 類型:時鐘倍頻器，零延遲緩沖器 PLL:帶旁路 輸入:LVTTL 輸出:LVTTL 電路數:1 比率 - 輸入:輸出:1:8 差分 - 輸入:輸出:無/無 頻率 - 最大:133.3MHz 除法器/乘法器:是/無 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:管件 其它名稱:23S08-5HPGG |
| ICS671M-06I | 制造商:ICS 制造商全稱:ICS 功能描述:3.3 VOLT ZERO DELAY, LOW SKEW BUFFER |
| ICS671M-06ILF | 制造商:ICS 制造商全稱:ICS 功能描述:3.3 VOLT ZERO DELAY, LOW SKEW BUFFER |
| ICS671M-06ILFT | 制造商:ICS 制造商全稱:ICS 功能描述:3.3 VOLT ZERO DELAY, LOW SKEW BUFFER |
| ICS671M-06IT | 制造商:ICS 制造商全稱:ICS 功能描述:3.3 VOLT ZERO DELAY, LOW SKEW BUFFER |
發布緊急采購，3分鐘左右您將得到回復。