- 您現在的位置：買賣IC網 > PDF目錄9022 > ICS291PGLFT (IDT, Integrated Device Technology Inc)IC CLK SYNTH TRPL PLL 20-TSSOP PDF資料下載
參數資料
| 型號： | ICS291PGLFT |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLK SYNTH TRPL PLL 20-TSSOP |
| 標準包裝： | 2,500 |
| 系列： | VersaClock™ |
| 類型： | 時鐘/頻率合成器 |
| PLL： | 帶旁路 |
| 輸入： | 時鐘，晶體 |
| 輸出： | CMOS |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:6 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 200MHz |
| 除法器/乘法器： | 是/是 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 291PGLFT |
ICS291
TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER
EPROM CLOCK SYNTHESIZER
IDT / ICS TRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER 3
ICS291
REV F 051310
External Components
The ICS291 requires a minimum number of external
components for proper operation.
Series Termination Resistor
Clock output traces over one inch should use series
termination. To series terminate a 50
trace (a commonly
used trace impedance), place a 33
resistor in series with
the clock line, as close to the clock output pin as possible.
The nominal impedance of the clock output is 20
.
Decoupling Capacitors
As with any high-performance mixed-signal IC, the ICS291
must be isolated from system power supply noise to perform
optimally.
Decoupling capacitors of 0.01F must be connected
between each VDD and the PCB ground plane. For
optimum device performance, the decoupling capacitor
should be mounted on the component side of the PCB.
Avoid the use of vias on the decoupling circuit.
Crystal Load Capacitors
The device crystal connections should include pads for
small capacitors from X1 to ground and from X2 to ground.
These capacitors are used to adjust the stray capacitance of
the board to match the nominally required crystal load
capacitance. Because load capacitance can only be
increased in this trimming process, it is important to keep
stray capacitance to a minimum by using very short PCB
traces (and no vias) between the crystal and device. Crystal
capacitors must be connected from each of the pins X1 and
X2 to ground.
The value (in pF) of these crystal caps should equal (CL -6
pF)*2. In this equation, CL= crystal load capacitance in pF.
Example: For a crystal with a 16 pF load capacitance, each
crystal capacitor would be 20 pF [(16-6) x 2 = 20].
ICS291 Configuration Capabilities
The architecture of the ICS291 allows the user to easily
configure the device to a wide range of output frequencies,
for a given input reference frequency.
The frequency multiplier PLL provides a high degree of
precision. The M/N values (the multiplier/divide values
available to generate the target VCO frequency) can be set
within the range of M = 1 to 1024 and N = 1 to 32,895.
The ICS291 also provides separate output divide values,
from 2 through 63, to allow the two output clock banks to
support widely differing frequency values from the same
PLL.
Each output frequency can be represented as:
Output Drive Control
The ICS291 has two output drive settings. For VDDO=VDD,
low drive should be selected when outputs are less than 100
MHz. High drive should be selected when outputs are
greater than 100 MHz.
For VDDO<2.8 V, high drive should be selected for all output
frequencies.
(Consult the AC Electrical Characteristics for output rise and
fall times for each drive option.)
IDT VersaClock Software
IDT applies years of PLL optimization experience into a user
friendly software that accepts the user’s target reference
clock and output frequencies and generates the lowest jitter,
lowest power configuration, with only a press of a button.
The user does not need to have prior PLL experience or
determine the optimal VCO frequency to support multiple
output frequencies.
VersaClock software quickly evaluates accessible VCO
frequencies with available output divide values and provides
an easy to understand, bar code rating for the target output
frequencies. The user may evaluate output accuracy,
performance trade-off scenarios in seconds.
Spread Spectrum Modulation
The ICS291 utilizes frequency modulation (FM) to distribute
energy over a range of frequencies. By modulating the
output clock frequencies, the device effectively lowers
energy across a broader range of frequencies; thus,
lowering a system’s electromagnetic interference (EMI). The
modulation rate is the time from transitioning from a
minimum frequency to a maximum frequency and then back
to the minimum.
OutputFreq
REFFreq
M
N
-----
=
相關PDF資料 |
PDF描述 |
|---|---|
| MK2703SLF | IC PLL AUD CLK SYNTHESIZER 8SOIC |
| SL38160ZIT | IC CLOCK SSCG 4PLL 5CH 16TSSOP |
| ICS601G-01ILFT | IC CLOCK MULTIPLIER 16-TSSOP |
| VE-BNY-MU-F2 | CONVERTER MOD DC/DC 3.3V 132W |
| VE-BNY-MU-F1 | CONVERTER MOD DC/DC 3.3V 132W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS291PGT | 功能描述:IC CLK SYNTH TRPL PLL 20-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:VersaClock™ 產品變化通告:Product Discontinuation 04/May/2011 標準包裝:96 系列:- 類型:時鐘倍頻器，零延遲緩沖器 PLL:帶旁路 輸入:LVTTL 輸出:LVTTL 電路數:1 比率 - 輸入:輸出:1:8 差分 - 輸入:輸出:無/無 頻率 - 最大:133.3MHz 除法器/乘法器:是/無 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:管件 其它名稱:23S08-5HPGG |
| ICS300 | 制造商:ICS 制造商全稱:ICS 功能描述:QTClock⑩ Quick Turn Clock Synthesizer |
| ICS3002AI01L | 制造商:ICS 制造商全稱:ICS 功能描述:FEMTOCLOCKS-TM CRYSTAL-TO- 3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER |
| ICS3002AI40 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:175MHZ, FEMTOCLOCKTM VCXO BASED SONET/SDH JITTER ATTENUATOR |
| ICS300-CA12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:300 Series CamclosureTM Camera System INTEGRATED CAMERA SYSTEM, INDOOR/OUTDOOR, WALL OR CEILING |
發布緊急采購，3分鐘左右您將得到回復。