- 您現在的位置：買賣IC網 > PDF目錄360746 > ICS2495 Dual Video/Memory Clock Generator PDF資料下載
參數資料
| 型號： | ICS2495 |
| 英文描述： | Dual Video/Memory Clock Generator |
| 中文描述： | 雙視頻/內存時鐘發生器 |
| 文件頁數： | 3/7頁 |
| 文件大?。?/td> | 314K |
| 代理商： | ICS2495 |
Buffered XTALOUT
In motherboard applications it may be desirable to have the
ICS2495
provide the bus clock for the rest of the system. This
eliminates the need for an additional 14.31818 MHz crystal
oscillator in the system, saving money as well as board space.
Depending on the load, it may be judicious to buffer XTA-
LOUT when using it to provide the system clock.
Output Circuit Considerations
As the dot clock is usually the highest frequency present in a
video graphics system, consideration should be given to EMI.
To minimize problems with meeting FCC EMI requirements,
the trace which connects
VCLK
or
MCLK
and other compo-
nents in the system should be kept as short as possible. The
ICS2495
outputs have been designed to minimize overshoot.
In addition, it may be helpful to place a ferrite bead in these
signal paths to limit the propagation of high-order harmonics
of this signal. A suitable device would be a Ferroxcube 56-590-
65/4B or equivalent. This device should be placed physically
close to the
ICS2495
. A 33 to 47 Ohm series resistor, some-
times called source termination, in this path may be necessary
to reduce ringing and reflection of the signal and may thereby
reduce phase jitter as well as EMI.
External Frequency Sources
EXTFREQ
on versions so equipped by the programming, is
an input to a digital multiplexer. When this input is enabled by
the FS0-3 selection, the signal driving pin 2 will appear at
VCLK (15)
instead of the PLL output. Internally, the PLL will
remain in lock at the frequency selected by the ROM code.
The programming option also exists to output the crystal oscil-
lator output on VCLK. In the case where XTAL1 is being
driven by an external oscillator, then this frequency would
appear on VCLK if so programmed.
Digital Inputs
FS0
(3)
,
FS1 (4)
,
FS2
(6)
, and
FS3 (7)
, are the TTL compatible
frequency select inputs for the binary code corresponding to
the frequency desired.
STROBE (5)
when high, allows new
data into the frequency select latches; and when low, prevents
address changes per Figure 2. The internal power-on-clear
signal will force an initial frequency code corresponding to an
all zeros input state.
MS0 (8)
and
MS1
(9)
are the correspond-
ing memory select inputs and are not strobed.
ICS2495
3
相關PDF資料 |
PDF描述 |
|---|---|
| ICS2495M | Dual Video/Memory Clock Generator |
| ICS2495N | Dual Video/Memory Clock Generator |
| ICS2509 | 3.3V Phase-Lock Loop Clock Driver |
| ICS2509C | 3.3V Phase-Lock Loop Clock Driver |
| ICS2509CyG-T | 3.3V Phase-Lock Loop Clock Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS2495M | 制造商:ICS 制造商全稱:ICS 功能描述:Dual Video/Memory Clock Generator |
| ICS2495M-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| ICS2495N | 制造商:ICS 制造商全稱:ICS 功能描述:Dual Video/Memory Clock Generator |
| ICS2495N-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| ICS2496M-452 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video/Graphics Clock Generator |
發布緊急采購，3分鐘左右您將得到回復。