- 您現在的位置：買賣IC網 > PDF目錄383086 > ICL7611DCBA (INTERSIL CORP) 1.4MHz, Low Power CMOS Operational Amplifiers PDF資料下載
參數資料
| 型號： | ICL7611DCBA |
| 廠商： | INTERSIL CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | 1.4MHz, Low Power CMOS Operational Amplifiers |
| 中文描述： | OP-AMP, 2000 uV OFFSET-MAX, 1.4 MHz BAND WIDTH, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, MS-012AA, SOIC-8 |
| 文件頁數： | 5/10頁 |
| 文件大?。?/td> | 100K |
| 代理商： | ICL7611DCBA |
5
Application Information
Static Protection
All devices are static protected by the use of input diodes.
However, strong static fields should be avoided, as it is
possible for the strong fields to cause degraded diode
junction characteristics, which may result in increased input
leakage currents.
Latchup Avoidance
Junction-isolated CMOS circuits employ configurations which
produce a parasitic 4-layer (PNPN) structure. The 4-layer
structure has characteristics similar to an SCR, and under
certain circumstances may be triggered into a low impedance
state resulting in excessive supply current. To avoid this
condition, no voltage greater than 0.3V beyond the supply
rails may be applied to any pin. In general, the op amp
supplies must be established simultaneously with, or before
any input signals are applied. If this is not possible, the drive
circuits must limit input current flow to 2mA to prevent latchup.
Choosing the Proper I
Q
The ICL7611 and ICL7612 have a similar I
Q
set-up scheme,
which allows the amplifier to be set to nominal quiescent
currents of 10
μ
A, 100
μ
A or 1mA. These current settings
change only very slightly over the entire supply voltage
range. The ICL7611/12 have an external I
Q
control terminal,
permitting user selection of quiescent current. To set the I
Q
connect the I
Q
terminal as follows:
I
Q
= 10
μ
A - I
Q
pin to V+
I
Q
= 100
μ
A - I
Q
pin to ground. If this is not possible, any
voltage from V+ - 0.8 to V- +0.8 can be used.
I
Q
= 1mA - I
Q
pin to V-
NOTE: The output current available is a function of the quiescent
current setting. For maximum peak-to-peak output voltage swings
into low impedance loads, IQ of 1mA should be selected.
Output Stage and Load Driving Considerations
Each amplifiers’ quiescent current flows primarily in the
output stage. This is approximately 70% of the I
Q
settings.
This allows output swings to almost the supply rails for
output loads of 1M
, 100k
, and 10k
, using the output
stage in a highly linear class A mode. In this mode,
crossover distortion is avoided and the voltage gain is
maximized. However, the output stage can also be operated
in Class AB for higher output currents. (See graphs under
Typical Operating Characteristics). During the transition from
Class A to Class B operation, the output transfer
characteristic is non-linear and the voltage gain decreases.
Input Offset Nulling
Offset nulling may be achieved by connecting a 25K pot
between the BAL terminals with the wiper connected to V+.
At quiescent currents of 1mA and 100
μ
A the nulling range
provided is adequate for all V
OS
selections; however with
I
Q
= 10
μ
A, nulling may not be possible with higher values
of V
OS
.
Frequency Compensation
The ICL7611 and ICL7612 are internally compensated, and
are stable for closed loop gains as low as unity with
capacitive loads up to 100pF.
Extended Common Mode Input Range
The ICL7612 incorporates additional processing which
allows the input CMVR to exceed each power supply rail by
0.1V for applications where V
SUPP
≥ ±
1.5V. For those
applications where V
SUPP
≤ ±
1.5V the input CMVR is limited
in the positive direction, but may exceed the negative supply
rail by 0.1V in the negative direction (e.g., for V
SUPPLY
=
±
1V,
the input CMVR would be +0.6V to -1.1V).
Operation At V
SUPPLY
=
±
1V
Operation at V
SUPPLY
=
±
1V is guaranteed at I
Q
= 10
μ
A for
A and B grades only.
Output swings to within a few millivolts of the supply rails are
achievable for R
L
≥
1M
. Guaranteed input CMVR is
±
0.6V
minimum and typically +0.9V to -0.7V at V
SUPPLY
=
±
1V. For
applications where greater common mode range is
desirable, refer to the description of ICL7612 above.
Typical Applications
The user is cautioned that, due to extremely high input
impedances, care must be exercised in layout, construction,
board cleanliness, and supply filtering to avoid hum and
noise pickup.
Note that in no case is I
Q
shown. The value of I
Q
must be
chosen by the designer with regard to frequency response
and power dissipation.
ICL7612
-
+
V
IN
V
OUT
R
L
≥
10K
FIGURE 1. SIMPLE FOLLOWER (NOTE 4)
ICL7612
+
-
V
IN
V
OUT
TO CMOS OR
LPTTL LOGIC
100K
+5
+5
1M
NOTE:
4. By using the ICL7612 in this application, the circuit will follow rail
to rail inputs.
FIGURE 2. LEVEL DETECTOR (NOTE 4)
ICL7611, ICL7612
相關PDF資料 |
PDF描述 |
|---|---|
| ICL7611DCBA-T | 1.4MHz, Low Power CMOS Operational Amplifiers |
| ICL7611BCPA | Multipoint-LVDS Quad Differential Line Driver 16-TSSOP -40 to 85 |
| ICL7611 | 1.4MHz, Low Power CMOS Operational Amplifiers(1.4MHz、低功耗CMOS運算放大器) |
| ICL7612 | 1.4MHz, Low Power CMOS Operational Amplifiers(1.4MHz、低功耗CMOS運算放大器) |
| ICL7641ECPD | Dual/Quad, Low Power CMOS Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICL7611DCBA-T | 功能描述:IC OPAMP 1.4MHZ CMOS LP 8-SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5 |
| ICL7611DCBAZ | 功能描述:運算放大器 - 運放 W/ANNEAL OPAMP 44KHZ LWBIAS 0 05NA COM RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| ICL7611DCBAZ-T | 功能描述:運算放大器 - 運放 W/ANNEAL OPAMP 44KHZ LWBIAS 0 05NA COM RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| ICL7611DCJD | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single/Dual/Triple/Quad Operational Amplifiers |
| ICL7611DCJE | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single/Dual/Triple/Quad Operational Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。