參數資料
型號: ICL7137
廠商: Intersil Corporation
元件分類: 串行ADC
英文描述: 3 1/2 Digit LED, Low Power Display,A/D Converters(3 1/2 位用于低功耗LED的A/D轉換器)
中文描述: 低功耗、3 1/2位A/D轉換器
文件頁數: 10/15頁
文件大小: 497K
代理商: ICL7137
10
FN3086.6
July 21, 2005
System Timing
Figure 7 shows the clocking arrangement used in the
ICL7136. Two basic clocking arrangements can be used:
1. Figure 9A, an external oscillator connected to DIP pin 40.
2. Figure 9B, an R-C oscillator using all three pins.
The oscillator frequency is divided by four before it clocks
the decade counters. It is then further divided to form the
three convert-cycle phases. These are signal integrate
(1000 counts), reference de-integrate (0 to 2000 counts) and
auto-zero (1000 to 3000 counts). For signals less than full
scale, auto-zero gets the unused portion of reference de-
integrate. This makes a complete measure cycle of 4,000
counts (16,000 clock pulses) independent of input voltage.
For three readings/second, an oscillator frequency of 48kHz
would be used.
To achieve maximum rejection of 60Hz pickup, the signal
integrate cycle should be a multiple of 60Hz. Oscillator
frequencies of 240kHz, 120kHz, 80kHz, 60kHz, 48kHz,
40kHz, 33
1
/
3
kHz, etc., should be selected. For 50Hz
rejection, Oscillator frequencies of 200kHz, 100kHz,
66
2
/
3
kHz, 50kHz, 40kHz, etc. would be suitable. Note that
40kHz (2.5 readings/sec.) will reject both 50Hz and 60Hz
(also 400Hz and 440Hz).
Component Value Selection
Integrating Resistor
Both the buffer amplifier and the integrator have a class A
output stage with 100
μ
A of quiescent current. They can
supply 1
μ
A of drive current with negligible nonlinearity. The
integrating resistor should be large enough to remain in this
very linear region over the input voltage range, but small
enough that undue leakage requirements are not placed on
the PC board. For 2V full scale, 1.8M
is near optimum and
similarly a 180k
for a 200mV scale.
Integrating Capacitor
The integrating capacitor should be selected to give the
maximum voltage swing that ensures tolerance buildup will
not saturate the integrator swing (approximately 0.3V from
either supply). In the ICL7136, when the analog COMMON
is used as a reference, a nominal +2V full-scale integrator
swing is fine. For three readings/second (48kHz clock)
nominal values for C
lNT
are 0.047
μ
F and 0.5
μ
F,
respectively. Of course, if different oscillator frequencies are
used, these values should be changed in inverse proportion
to maintain the same output swing.
An additional requirement of the integrating capacitor is that
it must have a low dielectric absorption to prevent roll-over
errors. While other types of capacitors are adequate for this
application, polypropylene capacitors give undetectable
errors at reasonable cost.
Auto-Zero Capacitor
The size of the auto-zero capacitor has some influence on
the noise of the system. For 200mV full scale where noise is
very important, a 0.47
μ
F capacitor is recommended. On the
2V scale, a 0.047
μ
F capacitor increases the speed of
recovery from overload and is adequate for noise on this
scale.
Reference Capacitor
A 0.1
μ
F capacitor gives good results in most applications.
However, where a large common mode voltage exists (i.e.,
the REF LO pin is not at analog COMMON) and a 200mV
scale is used, a larger value is required to prevent roll-over
error. Generally 1
μ
F will hold the roll-over error to 0.5 count
in this instance.
Oscillator Components
For all ranges of frequency a 180k
resistor is
recommended and the capacitor is selected from the
equation:
CLOCK
INTERNAL TO PART
40
39
38
3
4
TEST
CLOCK
INTERNAL TO PART
40
39
38
3
4
R
C
FIGURE 7B. RC OSCILLATOR
FIGURE 7. CLOCK CIRCUITS
FIGURE 7A. EXTERNAL OSCILLATOR
f
------------
For 48kHz Clock (3 Readings/s.),
=
C
50pF
.
=
ICL7136
相關PDF資料
PDF描述
ICL7605 HIGH RELIABILITY COMMUTATING AUTO - ZERO ( CAZ ) INSTRUMENTATION AMPLIFIER
ICL7606 HIGH RELIABILITY COMMUTATING AUTO - ZERO ( CAZ ) INSTRUMENTATION AMPLIFIER
ICL7612DCPAZ 1.4MHz, Low Power CMOS Operational Amplifiers
ICL7611DCBAZ 1.4MHz, Low Power CMOS Operational Amplifiers
ICL7611DCBAZ-T 1.4MHz, Low Power CMOS Operational Amplifiers
相關代理商/技術參數
參數描述
ICL7137C/D 功能描述:顯示驅動器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
ICL7137CDL 制造商:Rochester Electronics LLC 功能描述:- Bulk
ICL7137CJL 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ICL7137CM44 制造商:Rochester Electronics LLC 功能描述:44 PQFP, 0 + 70, 3 1/2 DIG A/D (LED DRIVE) - Bulk
ICL7137CMH 制造商:Maxim Integrated Products 功能描述:LOW POWER, 3 1/2 DIGIT ADC WITH DIRECT LED DR - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: