- 您現在的位置：買賣IC網 > PDF目錄384477 > ICL3232 (Intersil Corporation) 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF資料下載
參數資料
| 型號： | ICL3232 |
| 廠商： | Intersil Corporation |
| 元件分類： | RS-232 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | 5V的高速RS - 232收發器與0.1uF電容 |
| 文件頁數： | 14/17頁 |
| 文件大小： | 173K |
| 代理商： | ICL3232 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁
3-14
Devices with the automatic powerdown feature include an
INVALID output signal, which switches low to indicate that
invalid levels have persisted on all of the receiver inputs for
more than 30
μ
s (see Figure 7). INVALID switches high 1
μ
s
after detecting a valid RS-232 level on a receiver input.
INVALID operates in all modes (forced or automatic
powerdown, or forced on), so it is also useful for systems
employing manual powerdown circuitry. When automatic
powerdown is utilized, INVALID = 0 indicates that the
ICL32XX is in powerdown mode.
The time to recover from automatic powerdown mode is
typically 100
μ
s.
Receiver ENABLE Control (ICL3221/22/23/41 Only)
Several devices also feature an EN input to control the
receiver outputs. Driving EN high disables all the inverting
(standard) receiver outputs placing them in a high
impedance state. This is useful to eliminate supply current,
due to a receiver output forward biasing the protection diode,
when driving the input of a powered down (V
CC
= GND)
peripheral (see Figure 2). The enable input has no effect on
transmitter nor monitor (R
OUTB
) outputs.
Capacitor Selection
The charge pumps require 0.1
μ
F capacitors for 3.3V
operation. For other supply voltages refer to Table 3 for
capacitor values. Do not use values smaller than those listed
in Table 3. Increasing the capacitor values (by a factor of 2)
reduces ripple on the transmitter outputs and slightly
reduces power consumption. C
2
, C
3
, and C
4
can be
increased without increasing C
1
’s value, however, do not
increase C
1
without also increasing C
2
, C
3
, and C
4
to
maintain the proper ratios (C
1
to the other capacitors).
When using minimum required capacitor values, make sure
that capacitor values do not degrade excessively with
temperature. If in doubt, use capacitors with a larger nominal
value. The capacitor’s equivalent series resistance (ESR)
usually rises at low temperatures and it influences the
amount of ripple on V+ and V-.
Power Supply Decoupling
In most circumstances a 0.1
μ
F bypass capacitor is
adequate. In applications that are particularly sensitive to
power supply noise, decouple V
CC
to ground with a
capacitor of the same value as the charge-pump capacitor C
1
.
Connect the bypass capacitor as close as possible to the IC.
Transmitter Outputs when Exiting
Powerdown
Figure 8 shows the response of two transmitter outputs
when exiting powerdown mode. As they activate, the two
transmitter outputs properly go to opposite RS-232 levels,
with no glitching, ringing, nor undesirable transients. Each
transmitter is loaded with 3k
in parallel with 2500pF. Note
that the transmitters enable only when the magnitude of the
supplies exceed approximately 3V.
Mouse Driveability
The ICL324X have been specifically designed to power a
serial mouse while operating from low voltage supplies.
Figure 9 shows the transmitter output voltages under
increasing load current. The on-chip switching regulator
ensures the transmitters will supply at least
±
5V during worst
case conditions (15mA for paralleled V+ transmitters, 7.3mA
for single V- transmitter). The Automatic Powerdown feature
does not work with a mouse, so FORCEOFF and
FORCEON should be connected to V
CC
.
RECEIVER
INPUTS
TRANSMITTER
OUTPUTS
INVALID
OUTPUT
V+
V
CC
0
V-
V
CC
0
t
INVL
t
INVH
INVALID
REGION
}
FIGURE7. AUTOMATICPOWERDOWNANDINVALIDTIMING
DIAGRAMS
AUTOPWDN
PWR UP
TABLE 3. REQUIRED CAPACITOR VALUES
V
CC
(V)
C
1
(
μ
F)
C
2
, C
3
, C
4
(
μ
F)
3.0 to 3.6
0.1
0.1
4.5 to 5.5
0.047
0.33
3.0 to 5.5
0.1
0.47
TIME (20
μ
s/DIV.)
T1
T2
2V/DIV
5V/DIV
V
CC
= +3.3V
C1 - C4 = 0.1
μ
F
FORCEOFF
FIGURE 8. TRANSMITTER OUTPUTS WHEN EXITING
POWERDOWN
ICL3221 thru ICL3243
相關PDF資料 |
PDF描述 |
|---|---|
| ICL3241 | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3243 | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3227 | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3227CA | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3227IA | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICL3232CA | 功能描述:IC 2DRVR/2RCVR RS232 3V 16-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ICL3232CA-T | 功能描述:IC 2DRVR/2RCVR RS232 3V 16-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ICL3232CAZ | 功能描述:RS-232接口集成電路 RS232 3V 2D/2R COM RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ICL3232CAZ-T | 功能描述:RS-232接口集成電路 RS232 3V 2D/2R COMEL RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ICL3232CB | 功能描述:IC 2DRVR/2RCVR RS232 3V 16-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。