- 您現在的位置：買賣IC網 > PDF目錄383081 > ICL3221EIVZ (INTERSIL CORP) 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF資料下載
參數資料
| 型號： | ICL3221EIVZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 通用總線功能 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | LINE TRANSCEIVER, PDSO16 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MO-153AB, TSSOP-16 |
| 文件頁數： | 13/27頁 |
| 文件大?。?/td> | 860K |
| 代理商： | ICL3221EIVZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
13
FN4910.18
March 8, 2005
feature provides additional system power savings without
changes to the existing operating system.
Automatic powerdown operates when the FORCEON input
is low, and the FORCEOFF input is high. Tying FORCEON
high disables automatic powerdown, but manual powerdown
is always available via the overriding FORCEOFF input.
Table 2 summarizes the automatic powerdown functionality.
Devices with the automatic powerdown feature include an
INVALID output signal, which switches low to indicate that
invalid levels have persisted on all of the receiver inputs for
more than 30μs (see Figure 7). INVALID switches high 1μs
after detecting a valid RS-232 level on a receiver input.
INVALID operates in all modes (forced or automatic
powerdown, or forced on), so it is also useful for systems
employing manual powerdown circuitry. When automatic
powerdown is utilized, INVALID = 0 indicates that the
ICL32XXE is in powerdown mode.
The time to recover from automatic powerdown mode is
typically 100μs.
Receiver ENABLE Control
(ICL3221E, ICL3222E, ICL3223E, ICL3241E Only)
Several devices also feature an EN input to control the
receiver outputs. Driving EN high disables all the inverting
(standard) receiver outputs placing them in a high
impedance state. This is useful to eliminate supply current,
due to a receiver output forward biasing the protection diode,
when driving the input of a powered down (V
CC
= GND)
peripheral (see Figure 2). The enable input has no effect on
transmitter nor monitor (R
OUTB
) outputs.
Capacitor Selection
The charge pumps require 0.1μF capacitors for 3.3V
operation. For other supply voltages refer to Table 3 for
capacitor values. Do not use values smaller than those listed
in Table 3. Increasing the capacitor values (by a factor of 2)
reduces ripple on the transmitter outputs and slightly
reduces power consumption. C
2
, C
3
, and C
4
can be
increased without increasing C
1
’s value, however, do not
increase C
1
without also increasing C
2
, C
3
, and C
4
to
maintain the proper ratios (C
1
to the other capacitors).
When using minimum required capacitor values, make sure
that capacitor values do not degrade excessively with
temperature. If in doubt, use capacitors with a larger nominal
value. The capacitor’s equivalent series resistance (ESR)
usually rises at low temperatures and it influences the
amount of ripple on V+ and V-.
Power Supply Decoupling
In most circumstances a 0.1μF bypass capacitor is
adequate. In applications that are particularly sensitive to
power supply noise, decouple V
CC
to ground with a
capacitor of the same value as the charge-pump capacitor C
1
.
Connect the bypass capacitor as close as possible to the IC.
Operation Down to 2.7V
ICL32XXE transmitter outputs meet RS-562 levels (
±
3.7V),
at full data rate, with V
CC
as low as 2.7V. RS-562 levels
typically ensure interoperability with RS-232 devices.
Transmitter Outputs when Exiting
Powerdown
Figure 8 shows the response of two transmitter outputs
when exiting powerdown mode. As they activate, the two
transmitter outputs properly go to opposite RS-232 levels,
with no glitching, ringing, nor undesirable transients. Each
FIGURE 6. DEFINITION OF VALID RS-232 RECEIVER LEVELS
0.3V
-0.3V
-2.7V
2.7V
INVALID LEVEL - POWERDOWN OCCURS AFTER 30μs
VALID RS-232 LEVEL - ICL32XXE IS ACTIVE
VALID RS-232 LEVEL - ICL32XXE IS ACTIVE
INDETERMINATE - POWERDOWN MAY OR
MAY NOT OCCUR
INDETERMINATE - POWERDOWN MAY OR
MAY NOT OCCUR
RECEIVER
INPUTS
TRANSMITTER
OUTPUTS
INVALID
OUTPUT
V+
V
CC
0
V-
V
CC
0
t
INVL
t
INVH
INVALID
REGION
}
FIGURE 7. AUTOMATIC POWERDOWN AND INVALID
TIMING DIAGRAMS
AUTOPWDN
PWR UP
TABLE 3. REQUIRED CAPACITOR VALUES
V
CC
(V)
C
1
(μF)
C
2
, C
3
, C
4
(μF)
3.0 to 3.6
0.1
0.1
4.5 to 5.5
0.047
0.33
3.0 to 5.5
0.1
0.47
ICL3221E, ICL3222E, ICL3223E, ICL3232E, ICL3241E, ICL3243E
相關PDF資料 |
PDF描述 |
|---|---|
| ICL3222ECA | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3222ECA-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3222ECAZ | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3223ECA | RESISTOR, 5.11 K, SMD |
| ICL3223ECA-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICL3221EIVZ-T | 功能描述:RS-232接口集成電路 RS232 3V 1D/1R 15KV AUTODWN IND RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ICL3221EIVZ-T7A | 功能描述:RS-232接口集成電路 RS232 3V 1D/1R 15KV AUTODWN IND RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ICL3221EM | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:±15kV ESD Protected, +3V, 1μA, 250kbps, RS-232 Transmitters/Receivers |
| ICL3221EMVZ | 功能描述:RS-232接口集成電路 RS232 3V 1D/1R 15KV AUTODWN MIL TEMP RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ICL3221EMVZ-T | 功能描述:RS-232接口集成電路 RS232 3V 1D/1R 15KV AUTODWN MIL TEMP RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發布緊急采購，3分鐘左右您將得到回復。