- 您現在的位置：買賣IC網 > PDF目錄383081 > ICL3221EIA (INTERSIL CORP) 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF資料下載
參數資料
| 型號： | ICL3221EIA |
| 廠商： | INTERSIL CORP |
| 元件分類： | 通用總線功能 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | LINE TRANSCEIVER, PDSO16 |
| 封裝： | PLASTIC, MO-150AC, SSOP-16 |
| 文件頁數： | 15/27頁 |
| 文件大?。?/td> | 860K |
| 代理商： | ICL3221EIA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
15
FN4910.18
March 8, 2005
Interconnection with 3V and 5V Logic
The ICL32XX directly interface with 5V CMOS and TTL logic
families. Nevertheless, with the ICL32XX at 3.3V, and the logic
supply at 5V, AC, HC, and CD4000 outputs can drive ICL32XX
inputs, but ICL32XX outputs do not reach the minimum V
IH
for
these logic families. See Table 4 for more information.
±
15kV ESD Protection
All pins on ICL32XX devices include ESD protection
structures, but the ICL32XXE family incorporates advanced
structures which allow the RS-232 pins (transmitter outputs
and receiver inputs) to survive ESD events up to
±
15kV. The
RS-232 pins are particularly vulnerable to ESD damage
because they typically connect to an exposed port on the
exterior of the finished product. Simply touching the port
pins, or connecting a cable, can cause an ESD event that
might destroy unprotected ICs. These new ESD structures
protect the device whether or not it is powered up, protect
without allowing any latchup mechanism to activate, and
don’t interfere with RS-232 signals as large as
±
25V.
Human Body Model (HBM) Testing
As the name implies, this test method emulates the ESD
event delivered to an IC during human handling. The tester
delivers the charge through a 1.5k
current limiting resistor,
making the test less severe than the IEC61000 test which
utilizes a 330
limiting resistor. The HBM method
determines an IC’s ability to withstand the ESD transients
typically present during handling and manufacturing. Due to
the random nature of these events, each pin is tested with
respect to all other pins. The RS-232 pins on “E” family
devices can withstand HBM ESD events to
±
15kV.
IEC61000-4-2 Testing
The IEC61000 test method applies to finished equipment,
rather than to an individual IC. Therefore, the pins most likely
to suffer an ESD event are those that are exposed to the
outside world (the RS-232 pins in this case), and the IC is
tested in its typical application configuration (power applied)
rather than testing each pin-to-pin combination. The lower
current limiting resistor coupled with the larger charge
storage capacitor yields a test that is much more severe than
the HBM test. The extra ESD protection built into this
device’s RS-232 pins allows the design of equipment
meeting level 4 criteria without the need for additional board
level protection on the RS-232 port.
AIR-GAP DISCHARGE TEST METHOD
For this test method, a charged probe tip moves toward the
IC pin until the voltage arcs to it. The current waveform
delivered to the IC pin depends on approach speed,
humidity, temperature, etc., so it is difficult to obtain
repeatable results. The “E” device RS-232 pins withstand
±
15kV air-gap discharges.
CONTACT DISCHARGE TEST METHOD
During the contact discharge test, the probe contacts the
tested pin before the probe tip is energized, thereby
eliminating the variables associated with the air-gap
discharge. The result is a more repeatable and predictable
test, but equipment limits prevent testing devices at voltages
higher than
±
8kV. All “E” family devices survive
±
8kV contact
discharges on the RS-232 pins.
TABLE 4. LOGIC FAMILY COMPATIBILITY WITH VARIOUS
SUPPLY VOLTAGES
SYSTEM POWER-
SUPPLY VOLTAGE
(V)
V
CC
SUPPLY
VOLTAGE (V)
COMPATIBILITY
3.3
3.3
Compatible with all CMOS
families.
5
5
Compatible with all TTL and
CMOS logic families.
5
3.3
Compatible with ACT and HCT
CMOS, and with TTL. ICL32XX
outputs are incompatible with
AC, HC, and CD4000 CMOS
inputs.
Typical Performance Curves
V
CC
= 3.3V, T
A
= 25°C
FIGURE 13. TRANSMITTER OUTPUT VOLTAGE vs LOAD
CAPACITANCE
FIGURE 14. SLEW RATE vs LOAD CAPACITANCE
-6
-4
-2
0
2
4
6
1000
2000
3000
4000
5000
0
LOAD CAPACITANCE (pF)
T
1 TRANSMITTER AT 250kbps
1 OR 2 TRANSMITTERS AT 30kbps
V
OUT
+
V
OUT
-
LOAD CAPACITANCE (pF)
S
0
1000
2000
3000
4000
5000
5
10
15
20
25
+SLEW
-SLEW
ICL3221E, ICL3222E, ICL3223E, ICL3232E, ICL3241E, ICL3243E
相關PDF資料 |
PDF描述 |
|---|---|
| ICL3241EIA | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3221EIA-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3241EIA-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3221EIAZ | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3241EIAZ | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICL3221EIA-T | 功能描述:IC TXRX SGL RS232 3-5.5V 16SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ICL3221EIAZ | 功能描述:RS-232接口集成電路 RS232 3V 1D/1R 15KV AUTODWN 16SSOP IND RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ICL3221EIAZ | 制造商:Intersil Corporation 功能描述:Transceiver IC |
| ICL3221EIAZ-T | 功能描述:RS-232接口集成電路 RS232 3V 1D/1R 15KV AUTODWN IND RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ICL3221EIAZ-T7A | 功能描述:RS-232接口集成電路 RS232 3V 1D/1R 15KV AUTODWN IND RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發布緊急采購，3分鐘左右您將得到回復。