參數資料
型號: ICE3B0565J
廠商: INFINEON TECHNOLOGIES AG
英文描述: Off-Line SMPS Current Mode Controller with integrated 650V Startup Cell/Depletion CoolMOS⑩
中文描述: 離線式開關電源電流模式控制器,集成了?650V啟動細胞/消耗的CoolMOS⑩
文件頁數: 24/26頁
文件大?。?/td> 502K
代理商: ICE3B0565J
Version 2.3
24
8 May 2006
CoolSET-F3
ICE3Bxx65J
Schematic for recommended PCB layout
8
Schematic for recommended PCB layout
Figure 26 Schematic for recommended PCB layout
General guideline for PCB layout design using F3 CoolSET (refer to Figure 26):
1. “Star Ground “at bulk capacitor ground, C11:
“Star Ground “means all primary DC grounds should be connected to the ground of bulk capacitor C11
separately in one point. It can reduce the switching noise going into the sensitive pins of the CoolSET device
effectively. The primary DC grounds include the followings.
a. DC ground of the primary auxiliary winding in power transformer, TR1, and ground of C16 and Z11.
b. DC ground of the current sense resistor, R12
c. DC ground of the CoolSET device, GND pin of IC11; the signal grounds from C13, C14, C15 and collector of
IC12 should be connected to the GND pin of IC11 and then “star “connect to the bulk capacitor ground.
d. DC ground from bridge rectifier, BR1
e. DC ground from the bridging Y-capacitor, C4
2. High voltage traces clearance:
High voltage traces should keep enough spacing to the nearby traces. Otherwise, arcing would incur.
a. 400V traces (positive rail of bulk capacitor C11) to nearby trace: > 2.0mm
b. 600V traces (drain voltage of CoolSET IC11) to nearby trace: > 2.5mm
3. Filter capacitor close to the controller ground:
Filter capacitors, C13, C14 and C15 should be placed as close to the controller ground and the controller pin
as possible so as to reduce the switching noise coupled into the controller.
Guideline for PCB layout design when >3KV lightning surge test applied (refer to Figure 26):
1. Add spark gap
Spark gap is a pair of saw-tooth like copper plate facing each other which can discharge the accumulated
charge during surge test through the sharp point of the saw-tooth plate.
a. Spark Gap 3 and Spark Gap 4, input common mode choke, L1:
Gap separation is around 1.5mm (no safety concern)
C11
bulk cap
R11
D11
C12
IC12
R12
C13
C16
C15
C14
D13
R14
R23
R22
IC21
C23
R24
C22
R21
R25
GND
Vo
D21
C21
F3 CoolSET schematic for recommended PCB layout
R13
Z11
TR1
N
L
BR1
C2
Y-CAP
C3
Y-CAP
C1
X-CAP
L1
FUSE1
C4
Y-CAP
GND
Spark Gap 3
Spark Gap 4
D11
Spark Gap 1
Spark Gap 2
FB
CS
GND
NC
SOFTS/BL
VCC
F3
DRAIN
CoolSET
IC11
*
相關PDF資料
PDF描述
ICL232 +5V Powered, Dual RS-232 Transmitter/Receiver(正5V電源電壓、雙組RS-232收發器)
ICL3207E +/- 15kV ESD Protected, +3V to +5.5V, Low Power, 250kbps, RS-232 Transmitters/Receivers(+/- 15kV ESD防護, +3V至+5.5V, 低功率, 250kbps, RS-232收發器)
ICL3207ECB 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
ICL3207ECB-T 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
ICL3207ECBZ 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
相關代理商/技術參數
參數描述
ICE3B0565JFKLA1 制造商:Infineon Technologies AG 功能描述:Current Mode PWM Controller 650V 2A 8-Pin PDIP 制造商:Infineon Technologies AG 功能描述:AC/DC COOLSET - Rail/Tube 制造商:Infineon Technologies AG 功能描述:IC OFFLINE CTRLR SMPS OTP 8DIP
ICE3B0565JG 功能描述:電流型 PWM 控制器 Off-Line SMPS Currnt Mode CTRLR 650V RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
ICE3B0565JGXUMA1 制造商:Infineon Technologies AG 功能描述:Current Mode PWM Controller 650V 500mA 制造商:Infineon Technologies AG 功能描述:Current Mode PWM Controller 650V 500mA 12-Pin DSO 制造商:Infineon Technologies AG 功能描述:AC/DC COOLSET - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC OFFLINE CTRLR SMPS OTP DSO12
ICE3B0565JXKLA1 制造商:Infineon Technologies AG 功能描述:AC/DC COOLSET - Rail/Tube
ICE3B0565XKLA1 制造商:Infineon Technologies AG 功能描述:. 制造商:Infineon Technologies AG 功能描述:AC/DC COOLSET - Rail/Tube