- 您現在的位置：買賣IC網 > PDF目錄1923 > IA82510-PDW28I-R-01 (Innovasic Semiconductor)IC ASYNCHRONOUS SERIAL CTRL PDF資料下載
參數資料
| 型號： | IA82510-PDW28I-R-01 |
| 廠商： | Innovasic Semiconductor |
| 文件頁數： | 15/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ASYNCHRONOUS SERIAL CTRL |
| 標準包裝： | 325 |
| 系列： | * |
IA82510
Data Sheet
Asynchronous Serial Controller
February 25, 2011
IA211001219-05
http://www.Innovasic.com
UNCONTROLLED WHEN PRINTED OR COPIED
Customer Support:
Page 22 of 25
1-888-824-4184
Errata No. 11
Problem:
In semi-automatic/uLAN mode, the RX FIFO is only opened when an address
character matches the ACR1 or ACR0 registers (like full auto mode).
Description:
In semi-auto mode, the RX FIFO should open on any address character.
Workaround:
None.
Errata No. 12
Problem:
Device fails to reset interrupt signal in auto acknowledge mode when character is read
from RX FIFO.
Description:
RD strobe is outside the CS enable, which is outside of the Intel datasheet, but
apparently still works in the Intel device. Such a bus cycle allows the read data out, but fails to
generate the necessary internal strobe to change pointers. The same problem is found on write
accesses.
Workaround:
Force bus interface to bracket RD strobe inside the CS enable.
Errata No. 13
Problem:
RX FIFO locks up unexpectedly just after configuration and before starting reception.
Description:
An RCM command is executed with data of xB8. This is an “enable RX”, “flush
RX machine”, “flush RX FIFO”, and “l(fā)ock RX FIFO” command done in a single instruction. The
“flush RX machine” should unlock the RX FIFO, creating a conflict with the simultaneous “l(fā)ock
RX FIFO” command. The original Intel device apparently ignores or gives the “l(fā)ock RX FIFO”
command lower priority in this case. The IA82510 has this priority reversed. Apparently, the
application software in this case expected the “l(fā)ock RX FIFO” command to fail.
Workaround:
Do not execute a “flush RX FIFO” and “l(fā)ock RX FIFO” command simultaneously.
Break up into separate RCM commands.
相關PDF資料 |
PDF描述 |
|---|---|
| IA88C00-PLC68I-R-01 | IC MCU 8BIT 20MHZ 68PLCC |
| ICL232MJE | IC 2DRVR/2RCVR RS232 5V 16-DIP |
| ICL3217EIB-T | IC 5DRVR/3RCVR RS232 3V 24-SOIC |
| ICL3217IB-T | IC 5DRVR/3RCVR RS232 3V 24-SOIC |
| ICL3222CPZ | IC 2DRVR/2RCVR RS232 3V 18-PDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IA82510-PLC28C-00 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| IA82510-PLC28C-01 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| IA82510-PLC28I | 制造商:INNOVASIC 制造商全稱:INNOVASIC 功能描述:ASYNCHRONOUS SERIAL CONTROLLER |
| IA82510-PLC28I-00 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| IA82510-PLC28I-01 | 制造商:INNOVASIC 制造商全稱:INNOVASIC 功能描述:ASYNCHRONOUS SERIAL CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。