- 您現在的位置：買賣IC網 > PDF目錄385425 > HY5DU12822B (Hynix Semiconductor Inc.) CAP CERAMIC 15PF 50V NP0 0805 PDF資料下載
參數資料
| 型號： | HY5DU12822B |
| 廠商： | Hynix Semiconductor Inc. |
| 英文描述： | CAP CERAMIC 15PF 50V NP0 0805 |
| 中文描述： | 產品512Mb DDR SDRAM |
| 文件頁數： | 17/37頁 |
| 文件大?。?/td> | 396K |
| 代理商： | HY5DU12822B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Rev. 0.1 / May 2004
17
HY5DU12422B(L)TP
HY5DU12822B(L)TP
HY5DU121622B(L)TP
POWER-UP SEQUENCE AND DEVICE INITIALIZATION
DDR SDRAMs must be powered up and initialized in a predefined manner. Operational procedures other than those
specified may result in undefined operation. Power must first be applied to VDD, then to VDDQ, and finally to VREF
(and to the system VTT). VTT must be applied after VDDQ to avoid device latch-up, which may cause permanent dam-
age to the device. VREF can be applied anytime after VDDQ, but is expected to be nominally coincident with VTT.
Except for CKE, inputs are not recognized as valid until after VREF is applied. CKE is an SSTL_2 input, but will detect an
LVCMOS LOW level after VDD is applied. Maintaining an LVCMOS LOW level on CKE during power-up is required to
guarantee that the DQ and DQS outputs will be in the High-Z state, where they will remain until driven in normal oper-
ation (by a read access). After all power supply and reference voltages are stable, and the clock is stable, the DDR
SDRAM requires a 200us delay prior to applying an executable command.
Once the 200us delay has been satisfied, a DESELECT or NOP command should be applied, and CKE should be
brought HIGH. Following the NOP command, a PRECHARGE ALL command should be applied. Next a EXTENDED
MODE REGISTER SET command should be issued for the Extended Mode Register, to enable the DLL, then a MODE
REGISTER SET command should be issued for the Mode Register, to reset the DLL, and to program the operating
parameters. After the DLL reset, tXSRD(DLL locking time) should be satisfied for read command. After the Mode Reg-
ister set command, a PRECHARGE ALL command should be applied, placing the device in the all banks idle state.
Once in the idle state, two AUTO REFRESH cycles must be performed. Additionally, a MODE REGISTER SET command
for the Mode Register, with the reset DLL bit deactivated low (i.e. to program operating parameters without resetting
the DLL) must be performed. Following these cycles, the DDR SDRAM is ready for normal operation.
1.
Apply power - VDD, VDDQ, VTT, VREF in the following power up sequencing and attempt to maintain CKE at LVC-
MOS low state. (All the other input pins may be undefined.)
VDD and VDDQ are driven from a single power converter output.
VTT is limited to 1.44V (reflecting VDDQ(max)/2 + 50mV VREF variation + 40mV VTT variation.
VREF tracks VDDQ/2.
A minimum resistance of 42 Ohms (22 ohm series resistor + 22 ohm parallel resistor - 5% tolerance) limits the
input current from the VTT supply into any pin.
If the above criteria cannot be met by the system design, then the following sequencing and voltage relation-
ship must be adhered to during power up.
2.
Start clock and maintain stable clock for a minimum of 200usec.
3.
After stable power and clock, apply NOP condition and take CKE high.
4.
Issue Extended Mode Register Set (EMRS) to enable DLL.
5.
Issue Mode Register Set (MRS) to reset DLL and set device to idle state with bit A8=high. (An additional 200
cycles(tXSRD) of clock are required for locking DLL)
6.
Issue Precharge commands for all banks of the device.
Voltage description
Sequencing
Voltage relationship to avoid latch-up
VDDQ
After or with VDD
< VDD + 0.3V
VTT
After or with VDDQ
< VDDQ + 0.3V
VREF
After or with VDDQ
< VDDQ + 0.3V
相關PDF資料 |
PDF描述 |
|---|---|
| HY5DU121622B | 512Mb DDR SDRAM |
| HY5DU121622BLTP | 512Mb DDR SDRAM |
| HY5DU121622BLTP-X | 512Mb DDR SDRAM |
| HY5DU121622BTP | 512Mb DDR SDRAM |
| HY5DU121622BTP-X | 512Mb DDR SDRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HY5DU12822BLT | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512Mb DDR SDRAM |
| HY5DU12822BLTP | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512Mb DDR SDRAM |
| HY5DU12822BLTP-X | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512Mb DDR SDRAM |
| HY5DU12822BT | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512Mb DDR SDRAM |
| HY5DU12822BTP | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512Mb DDR SDRAM |
發布緊急采購，3分鐘左右您將得到回復。