參數資料
型號: HY29F800BR-55
廠商: HYNIX SEMICONDUCTOR INC
元件分類: DRAM
英文描述: x8/x16 Flash EEPROM
中文描述: 512K X 16 FLASH 5V PROM, 55 ns, PDSO48
封裝: REVERSE, TSOP-48
文件頁數: 9/40頁
文件大?。?/td> 509K
代理商: HY29F800BR-55
9
Rev. 4.2/May 01
HY29F800
The flow chart in Figure 1 illustrates the proce-
dure for protecting sectors, and timing specifica-
tions and waveforms are shown in the specifica-
tions section of this document. Verification of pro-
tection is accomplished as described in the Elec-
tronic ID Mode section and shown in the flow chart.
The procedure for sector unprotection is illustrated
in the flow chart in Figure 2, and timing specifica-
tions and waveforms are given at the end of this
document.
Note that to unprotect any sector, all
unprotected sectors must first be protected prior
to the first unprotect write cycle.
Sectors can also be
temporarily
unprotected as
described in the next section.
Temporary Sector Unprotect Operation
This feature allows temporary unprotection of pre-
viously protected sectors to allow changing the
data in-system. Temporary Sector Unprotect
mode is activated by setting the RESET# pin to
START
NOTE: All sectors must be
previously protected.
Set: TRYCNT = 1
Set: A9 = CE# = OE# = V
ID
Set: RESET# = V
IH
WE# = V
IL
Wait t
WPP2
Set:
A9 = V
OE# = CE# = V
IL
Read Data
Data = 0x00
NSEC = 18
YES
TRYCNT = 1000
NO
Increment TRYCNT
NO
YES
DEVICE FAILURE
NO
YES
Remove V
ID
from A9
SECTOR UNPROTECT
COMPLETE
APPLY V
CC
Set Sector Group Address:
A[18:12] = Sector NSEC
A0 = A6 = V
IL
A1 = V
IH
NSEC = NSEC + 1
Set: NSEC = 0
WE# = V
IH
Figure 2. Sector Unprotect Procedure
V
ID
. While in this mode, formerly protected sec-
tors can be programmed or erased by invoking
the appropriate commands (see Device Com-
mands section). Once V
ID
is removed from RE-
SET#, all the previously protected sectors are pro-
tected again. Figure 3 illustrates the algorithm.
Electronic ID Mode Operation
The Electronic ID mode provides manufacturer and
device identification and sector protection verifi-
cation through identifier codes output on DQ[7:0]
or DQ[15:0]. This mode is intended primarily for
programming equipment to automatically match
a device to be programmed with its correspond-
ing programming algorithm. The Electronic ID in-
formation can also be obtained by the host through
a command sequence, as described in the De-
vice Commands section.
Operation in the Electronic ID mode requires V
ID
on address pin A[9], with additional requirements
相關PDF資料
PDF描述
HY29F800BR-70 x8/x16 Flash EEPROM
HY29F800BR-90 x8/x16 Flash EEPROM
HY29F800BT-12 x8/x16 Flash EEPROM
HY29F800BT-55 x8/x16 Flash EEPROM
HY29F800TT-55 x8/x16 Flash EEPROM
相關代理商/技術參數
參數描述
HY29F800BR-55E 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8/x16 Flash EEPROM
HY29F800BR-55I 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8/x16 Flash EEPROM
HY29F800BR-70 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:x8/x16 Flash EEPROM
HY29F800BR-70E 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8/x16 Flash EEPROM
HY29F800BR-70I 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8/x16 Flash EEPROM