參數資料
型號: HY29F400BR90
廠商: Hynix Semiconductor Inc.
英文描述: 4 Megabit (512Kx8/256Kx16) 5 Volt-only Flash Memory
中文描述: 4兆位(512Kx8/256Kx16)5伏只閃存
文件頁數: 2/40頁
文件大?。?/td> 509K
代理商: HY29F400BR90
2
Rev. 5.2/May 01
HY29F400
cessors. A 55 ns version operating over 5.0 volts
± 5% is also available. To eliminate bus conten-
tion, the HY29F400 has separate chip enable
(CE#), write enable (WE#) and output enable
(OE#) controls.
The device is compatible with the JEDEC single
power-supply Flash command set standard. Com-
mands are written to the command register using
standard microprocessor write timings, from where
they are routed to an internal state-machine that
controls the erase and programming circuits.
Device programming is performed a byte or word
at a time by executing the four-cycle Program com-
mand. This initiates an internal algorithm that au-
tomatically times the program pulse widths and
verifies proper cell margin.
The HY29F400
s sector erase architecture allows
any number of array sectors to be erased and re-
programmed without affecting the data contents
of other sectors. Device erasure is initiated by
executing the Erase command. This initiates an
internal algorithm that automatically preprograms
the array (if it is not already programmed) before
executing the erase operation. During erase
cycles, the device automatically times the erase
pulse widths and verifies proper cell margin.
To protect data in the device from accidental or
unauthorized attempts to program or erase the
BLOCK DIAGRAM
device while it is in the system (e.g., by a virus),
the device has a Sector Protect function which
hardware write protects selected sectors. The
sector protect and unprotect features can be en-
abled in a PROM programmer. Temporary Sec-
tor Unprotect, which requires a high voltage, al-
lows in-system erasure and code changes in pre-
viously protected sectors.
Erase Suspend enables the user to put erase on
hold for any period of time to read data from, or
program data to, any sector that is not selected
for erasure. True background erase can thus be
achieved. The device is fully erased when shipped
from the factory.
Addresses and data needed for the programming
and erase operations are internally latched during
write cycles, and the host system can detect
completion of a program or erase operation by
observing the RY/BY# pin, or by reading the DQ[7]
(Data# Polling) and DQ[6] (Toggle) status bits.
Reading data from the device is similar to reading
from SRAM or EPROM devices. Hardware data
protection measures include a low V
CC
detector
that automatically inhibits write operations during
power transitions.
The host can place the device into the standby
mode. Power consumption is greatly reduced in
this mode.
STATE
CONTROL
WE#
CE#
OE#
BYTE#
COMMAND
REGISTER
DQ[15:0]
A[17:0], A-1
V
CC
DETECTOR
TIMER
ERASE VOLTAGE
GENERATOR AND
SECTOR SWITCHES
PROGRAM
VOLTAGE
GENERATOR
A
X-DECODER
Y-DECODER
4 Mb FLASH
MEMORY
ARRAY
Y-GATING
DATA LATCH
I/O BUFFERS
I/O CONTROL
RESET#
DQ[15:0]
A[17:0], A-1
RY/BY#
相關PDF資料
PDF描述
HY29F400BT70 4 Megabit (512Kx8/256Kx16) 5 Volt-only Flash Memory
HY29F400BT90 4 Megabit (512Kx8/256Kx16) 5 Volt-only Flash Memory
HY29F400TG45 4 Megabit (512Kx8/256Kx16) 5 Volt-only Flash Memory
HY29F400TG55 4 Megabit (512Kx8/256Kx16) 5 Volt-only Flash Memory
HY29F400TG90 4 Megabit (512Kx8/256Kx16) 5 Volt-only Flash Memory
相關代理商/技術參數
參數描述
HY29F400BR-90 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:x8/x16 Flash EEPROM
HY29F400BT45 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:4 Megabit (512Kx8/256Kx16) 5 Volt-only Flash Memory
HY29F400BT-45 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:x8/x16 Flash EEPROM
HY29F400BT55 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:4 Megabit (512Kx8/256Kx16) 5 Volt-only Flash Memory
HY29F400BT-55 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:x8/x16 Flash EEPROM