- 您現在的位置：買賣IC網 > PDF目錄367286 > HY229F800TR-90I EEPROM PDF資料下載
參數資料
| 型號： | HY229F800TR-90I |
| 元件分類： | EEPROM |
| 英文描述： | EEPROM |
| 中文描述： | EEPROM的 |
| 文件頁數： | 9/40頁 |
| 文件大?。?/td> | 310K |
| 代理商： | HY229F800TR-90I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
9
Rev. 4.0/Jan. 00
HY29F800
The flow chart in Figure 1 illustrates the proce-
dure for protecting sectors, and timing specifica-
tions and waveforms are shown in the specifica-
tions section of this document. Verification of pro-
tection is accomplished as described in the Elec-
tronic ID Mode section and shown in the flow chart.
The procedure for sector unprotection is illustrated
in the flow chart in Figure 2, and timing specifica-
tions and waveforms are given at the end of this
document. Note that to unprotect any sector, all
unprotected sectors must first be protected prior
to the first unprotect write cycle.
Sectors can also be temporarily unprotected as
described in the next section.
Temporary Sector Unprotect Operation
This feature allows temporary unprotection of pre-
viously protected sectors to allow changing the
data in-system. Temporary Sector Unprotect
mode is activated by setting the RESET# pin to
START
NOTE: All sectors must be
previously protected.
Set: TRYCNT = 1
Set: A9 = CE# = OE# = V
ID
Set: RESET# = V
IH
WE# = V
IL
Wait t
WPP2
Set:
A9 = V
OE# = CE# = V
IL
Read Data
Data = 0x00
NSEC = 18
YES
TRYCNT = 1000
NO
Increment TRYCNT
NO
YES
DEVICE FAILURE
NO
YES
Remove V
ID
from A9
SECTOR UNPROTECT
COMPLETE
APPLY V
CC
Set Sector Group Address:
A[18:12] = Sector NSEC
A0 = A6 = V
IL
A1 = V
IH
NSEC = NSEC + 1
Set: NSEC = 0
WE# = V
IH
Figure 2. Sector Unprotect Procedure
V
ID
. While in this mode, formerly protected sec-
tors can be programmed or erased by invoking
the appropriate commands (see Device Com-
mands section). Once V
ID
is removed from RE-
SET#, all the previously protected sectors are pro-
tected again. Figure 3 illustrates the algorithm.
Electronic ID Mode Operation
The Electronic ID mode provides manufacturer and
device identification and sector protection verifi-
cation through identifier codes output on DQ[7:0]
or DQ[15:0]. This mode is intended primarily for
programming equipment to automatically match
a device to be programmed with its correspond-
ing programming algorithm. The Electronic ID in-
formation can also be obtained by the host through
a command sequence, as described in the De-
vice Commands section.
Operation in the Electronic ID mode requires V
ID
on address pin A[9], with additional requirements
相關PDF資料 |
PDF描述 |
|---|---|
| HY229F800TT-12 | EEPROM |
| HY229F800TT-12I | EEPROM |
| HY229F800TT-55 | EEPROM |
| HY229F800TT-55I | EEPROM |
| HY229F800TT-70 | EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HY229F800TT-12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
| HY229F800TT-12I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
| HY229F800TT-55 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
| HY229F800TT-55I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
| HY229F800TT-70 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
發布緊急采購，3分鐘左右您將得到回復。