- 您現在的位置：買賣IC網 > PDF目錄370731 > HW125F Analog IC PDF資料下載
參數資料
| 型號： | HW125F |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 373K |
| 代理商： | HW125F |
Lucent Technologies Inc.
7
HW125F Power Modules; dc-dc Converters:
36 Vdc to 75 Vdc Input, 3.3 Vdc Output; 83.5 W
Data Sheet
August 2000
Test Configurations
8-203(C).l
Note: Measure input reflected-ripple current with a simulated source
inductance (L
TEST
) of 12
μ
H. Capacitor C
S
offsets possible bat-
tery impedance. Measure current as shown above.
Figure 9. Input Reflected-Ripple Test Setup
8-513(C).d
Note: Use a 1.0
μ
F ceramic capacitor and a 10
μ
F aluminum or
tantalum capacitor. Scope measurement should be made
using a BNC socket. Position the load between
51 mm and 76 mm (2 in. and 3 in.) from the module.
Figure 10. Peak-to-Peak Output Noise
Measurement Test Setup
8-749(C)
Note: All measurements are taken at the module terminals. When
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contact resistance.
Figure 11. Output Voltage and Efficiency
Measurement Test Setup
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power mod-
ule. For the test configuration in Figure 9, a 33
μ
F elec-
trolytic capacitor (ESR < 0.7
at 100 kHz) mounted
close to the power module helps ensure stability of the
unit. For other highly inductive source impedances,
consult the factory for further application guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL 1950, CSAC22.2 No. 950-95, and VDE0805
(EN60950, IEC950).
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75 Vdc), for the module's output to be considered
meeting the requirements of safety extra-low voltage
(SELV), all of the following must be true:
I
The input source is to be provided with reinforced
insulation from any other hazardous voltages, includ-
ing the ac mains.
I
One V
I
pin and one V
O
pin are to be grounded, or
both the input and output pins are to be kept floating.
I
The input pins of the module are not operator acces-
sible.
I
Another SELV reliability test is conducted on the
whole system, as required by the safety agencies, on
the combination of supply source and the subject
module to verify that under a single fault, hazardous
voltages do not appear at the module's output.
Note:
Do not ground either of the input pins of the
module without grounding one of the output
pins. This may allow a non-SELV voltage to
appear between the output pins and ground.
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
TO OSCILLOSCOPE
12 μH
V
I
(+)
V
I
(–)
CURRENT
PROBE
L
TEST
BATTERY
C
S
220 μF
ESR < 0.1
@ 20
°
C, 100 kHz
33 μF
ESR < 0.7
@ 100 kHz
V
O
(+)
V
O
(–)
1.0 μF
RESISTIVE
LOAD
SCOPE
COPPER STRIP
10 μF
CONTACT AND
DISTRIBUTION LOSSES
V
I
(+)
I
I
I
O
SUPPLY
CONTACT
RESISTANCE
CONTACT AND
DISTRIBUTION LOSSES
SENSE(+)
V
I
(–)
V
O
(+)
V
O
(–)
SENSE(–)
η
V
(+) – V
(–)
V
I
(+) – V
I
(–)
[
[
------------------------------------------------
]
I
O
]
I
I
x 100 %
=
相關PDF資料 |
PDF描述 |
|---|---|
| HW300B | ?High-sensitivity InSb Hall element. ?SIP package. ?Shipped in bulk (500pcs per pack). |
| HW302B | ?High-sensitivity InSb Hall element. ?Thin SIP package. ?Shipped in bulk (500pcs per pack). |
| HW321A | WHITE HIGH FLUX LED |
| HW331A | WHITE HIGH FLUX LED |
| HW941A | WHITE HIGH FLUX LED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HW127 | 制造商:NTE Electronics 功能描述: |
| HW127111109 | 功能描述:打印機 LABEL RoHS:否 制造商:Seiko Instruments 產品:Printer 電源電壓: 每行點數:9 x 320 打印速度:52.5 cps, 80 cps 紙張寬度:112 mm |
| HW-127111-10-9 | 功能描述:LABEL ID PRODUCT RoHS:是 類別:計算機，辦公室 - 元件，配件 >> 標簽，標記 系列:HW 標準包裝:1 系列:PANACEA™ 類型:標簽 標簽類型:熱敏式 標簽尺寸:0.75" x 26.2'（19.1mm x 8.0m） 材質:聚酯 顏色:透明 適用于相關產品:熱敏打印機 包裝:卷 其它名稱:298-1346 |
| HW-127127-10-9 | 功能描述:電線鑒定 HW .5/.5" LABEL PRICE PER LABEL RoHS:否 制造商:TE Connectivity / Q-Cees 產品:Labels and Signs 類型: 材料:Vinyl 顏色:Blue 寬度:0.625 in 長度:1 in |
| HW128/12- | 制造商:ROEBUCK 功能描述:ROEBUCK SASH BRUSH 3/4"D |
發布緊急采購，3分鐘左右您將得到回復。