- 您現在的位置：買賣IC網 > PDF目錄384450 > HV100 (Supertex, Inc.) 3-Pin Hotswap, Inrush Current Limiter Controllers PDF資料下載
參數資料
| 型號： | HV100 |
| 廠商： | Supertex, Inc. |
| 元件分類： | 脈沖抑制器 |
| 英文描述： | 3-Pin Hotswap, Inrush Current Limiter Controllers |
| 中文描述： | 3針熱插拔，浪涌電流限制器控制器 |
| 文件頁數： | 5/5頁 |
| 文件大小： | 83K |
| 代理商： | HV100 |
5
HV100/HV101
1235 Bordeaux Drive, Sunnyvale, CA 94089
TEL: (408) 744-0100
FAX: (408) 222-4895
www.supertex.com
08/26/02 rev.3b
2002 Supertex Inc. All rights reserved. Unauthorized use or reproduction prohibited.
Application Information, cont’d.
Auto-Retry
Not only does the HV100/HV101 provide short circuit protection
in a 3-pin package, it also includes a 2.5s built in auto-restart
timer. The HV100/HV101 will continuously try to turn on the
system every 2.5s, providing sufficient time for the pass element
to cool down after each attempt.
Calculating Inrush Current
As can be seen in the diagram below, for a standard pass
element, the HV100/HV101 will normalize the hotswap time
period against load capacitance. For this reason the current limit
will increase with increasing value of the load capacitance.
Inrush can be calculated from the following formula:
INRUSH(PEAK)
ISS
RSS
LOAD
This is a surprisingly consistent result because for most MOSFETs
of a particular type the ratio of C
/ C
is relatively constant
(though notice from the plot that there is some variation) even
while the absolute value of these and other quantities vary.
Based on this, the inrush current will vary primarily with C
.
This makes designing with the HV100/HV101 particularly easy
because once the pass element is chosen, the period is fixed and
the inrush varies with C
LOAD
only.
Programming the HV100/HV101
The HV100/HV101 require no external components other than a
pass element to provide the functionality described thus far. In
some applications it may be useful to use external components
to adjust the maximum allowable inrush current, adjust UVLO, or
to provide additional gate clamping if the supply rails have rise
times below 1ms.
All of the above are possible with a minimum number of external
components.
i)
To adjust inrush current with an external component simply
connect a capacitor (C
) from drain to gate of the MOSFET.
The inrush calculation then becomes:
I
INRUSH
= (C
ISS
/ (C
RSS
+ C
FB
)) * 2.5e3 * C
LOAD
Note that a resistor (approximately 10K
) needs to be
added in series with C
to create a zero in the feedback loop
and limit the spurious turn on which is now enhanced by the
larger divider element.
ii)
To increase undervoltage lockout simply connect a Zener
diode in series with the V
PP
pin.
If the V
rises particularly fast (>48e6V/s) then it may be
desirable to connect a capacitor from gate to source of the
MOSFET to provide a path for the power application tran-
sient spike, which is now too fast for the internal clamping
mechanism.
iii)
iv)
To limit the peak current during a short circuit, a resistor in
series with the source of the MOSFET may help.
Implementing PWRGD Control
Due to the HV100/HV101
’
s small footprint, it is possible to create
an open drain PWRGD signal using external components and
still maintain a size comparable with the smallest hotswap
controllers available elsewhere. To accomplish this an external
MOSFET may be used in conjunction with the gate output.
Simply use a high impedance divider (10M
) sized so that the
open drain PWRGD MOSFET threshold will only be reached
once the HV100/HV101
’
s gate voltage rises well above the
current limit value required by the external MOSFET pass
device. Alternatively a Zener diode between the gate output and
the PWRGD MOSFET gate set at a voltage higher than the
maximum pass element Vt will also work.
2A/div
HV100
PWGRD
相關PDF資料 |
PDF描述 |
|---|---|
| HV100DB1 | 3-Pin Hotswap Controller |
| HV100K5 | 3-Pin Hotswap, Inrush Current Limiter Controllers |
| HV100K6 | 3-Pin Hotswap, Inrush Current Limiter Controllers |
| HV100X | 3-Pin Hotswap, Inrush Current Limiter Controllers |
| HV20220 | Low Charge Injection 8-Channel High Voltage Analog Switch(低電荷射入8通道高壓模擬開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HV100_07 | 制造商:SUPERTEX 制造商全稱:SUPERTEX 功能描述:3-Pin Hotswap, Inrush Current Limiter Controllers (Negative Supply Rail) |
| HV100001 | 制造商:DIGIMESS 功能描述:PSU BENCH HIGH VOLTAGE |
| HV100DB1 | 功能描述:電源管理IC開發工具 HV100 Demo Brd RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HV100K5 | 功能描述:熱插拔功率分布 Negative RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HV100K5-G | 功能描述:熱插拔功率分布 Negative RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。