- 您現在的位置：買賣IC網 > PDF目錄385407 > HT93LC56 (Holtek Semiconductor Inc.) 2K 3-Wire CMOS Serial EEPROM PDF資料下載
參數資料
| 型號： | HT93LC56 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 2K 3-Wire CMOS Serial EEPROM |
| 中文描述： | 2K 3線的CMOS串行EEPROM |
| 文件頁數： | 5/10頁 |
| 文件大?。?/td> | 375K |
| 代理商： | HT93LC56 |
Timing Diagrams
Functional Description
The HT93LC56 is accessed via a three-wire serial
communication interface. The device is arranged
into 128 words by 16 bits or 256 words by 8 bits
depending whether the ORG pin is connected to
VCC or VSS. The HT93LC56 contains seven in-
structions: RE AD, E RASE , WRITE , E WE N,
EWDS, ERAL and WRAL . When the user se-
lectable internal organization is arranged
into 128
×
16 (256
×
8), these instructions are all
made up of 11(12) bits data: 1 start bit, 2 op code
bits and 8(9) address bits.
By using the control signal CS, SK and data
input signal DI, these instructions can be given
to the HT93LC56. These serial instruction data
presented at the DI input will be written into
the device at the rising edge of SK . During the
READ cycle, DO pin acts as the data output and
during the WRITE or E RASE cycle, DO pin
indicates the BUSY/READY status. When the
DO pin is active for read data or as a
BUSY/READY indicator the CS pin must be
high; otherwise DO pin will be in a high-imped-
ance state. For successful instructions, CS must
be low once after the instruction is sent. After
power on, the device is by default in the EWDS
state. And, an E WE N instruction must be per-
formed before any ERASE or WRITE instruc-
tion can be executed. The following are the
functional descriptions and timing diagrams of
all seven instructions.
READ
The READ instruction will stream out data at a
specified address on the DO pin. The data on
DO pin changes during the low-to-high edge of
SK signal. The 8 bits or 16 bits data stream is
preceded by a logical “0” dummy bit. Irrespec-
tive of the condition of the E WE N or E WDS
instruction, the RE AD command is always
valid and independent of these two instruc-
tions. After the data word has been read the
internal address will be automatically incre-
mented by 1 allowing the next consecutive data
word to be read out without entering further
address data. The address will wrap around
with CS High until CS returns to LOW.
EWEN/EWDS
The EWE N/E WDS instruction will enable or
disable the programming capabilities. At both
the power on and power off state the device auto-
matically entered the disable mode. Before a
WRITE, ERASE, WRAL or ERAL instruction is
given, the programming enable instruction
E WE N must be issued, otherwise the
ERASE/WRITE instruction is invalid. After the
EWEN instruction is issued, the programming
enable condition remains until power is turned off
or a EWDS instruction is given. No data can be
written into the device in the programming dis-
abled state. By so doing, the internal memory
data can be protected.
HT93LC56
5
6th May ’99
相關PDF資料 |
PDF描述 |
|---|---|
| HT93LC66 | 4K 3-Wire CMOS Serial EEPROM |
| HT93LC86 | CMOS 16K 3-Wire Serial EEPROM |
| HT9480 | Pager Controller |
| HT95168 | Caller ID Telephone IC |
| HT9580 | Character Pager Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT93LC56-(8SOIC) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microwire Serial EEPROM |
| HT93LC56-8DIP-A | 制造商:Holtek Semiconductor Inc 功能描述:IC EEPROM SERIAL 2K 93LC56 DIP8 |
| HT93LC56-8DIP-A | 制造商:Holtek Semiconductor Inc 功能描述:IC EEPROM SERIAL 2K 93LC56 DIP8 |
| HT93LC56-8SOP-A | 制造商:Holtek Semiconductor Inc 功能描述:IC EEPROM SERIAL 2K 93LC56 SOIC8 |
| HT93LC56-8SOP-A | 制造商:Holtek Semiconductor Inc 功能描述:IC EEPROM SERIAL 2K 93LC56 SOIC8 |
發布緊急采購，3分鐘左右您將得到回復。