- 您現在的位置：買賣IC網 > PDF目錄385406 > HT9302G (Holtek Semiconductor Inc.) 1-Memory/2-Memory Tone/Pulse Dialer PDF資料下載
參數資料
| 型號： | HT9302G |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 1-Memory/2-Memory Tone/Pulse Dialer |
| 中文描述： | 1-Memory/2-Memory音頻/脈沖撥號器 |
| 文件頁數： | 3/27頁 |
| 文件大?。?/td> | 284K |
| 代理商： | HT9302G |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Keyboard Information
Pin Description
Pin Name
I/O
Internal
Connection
Description
C1~C4
R1~R4
I/O
CMOS IN/OUT
These pins form a 4 4 keyboard matrix which can perform keyboard input detec-
tion and dialing specification setting functions. When on-hook (HKS=high) all the
pins are set high. While off-hook the column group (C1~C4) remains low and the
row group (R1~R4) is set high for key input detection.
An inexpensive single contact 4 4 keyboard can be used as an input device.
Pressing a key connects a single column to a single row, and actuates the system
oscillatorthatresultsinadialingsignaloutput.Ifmorethantwokeysarepressedat
the same time, no response occurs. The key-in debounce time is 20ms. Refer to
the keyboard information for keyboard arrangement and to the functional descrip-
tion for dialing specification selection.
X1
I
OSCILLATOR
The system oscillator consists of an inverter, a bias resistor and the necessary
load capacitor on chip. Connecting a standard 3.579545MHz crystal or ceramic
resonator to the X1 and X2 terminals can implement the oscillator function. The
oscillator is turned off in the standby mode, and is actuated whenever a key-
board entry is detected.
X2
O
XMUTE
O
NMOS OUT
XMUTE is an NMOS open drain structure pulled to VSS during dialing signal
transmission. Otherwise, it is an open circuit. The XMUTE is used to mute the
speech circuit when transmitting the dial signal.
HKS
I
CMOS IN
This pin is used to monitor the status of the hook-switch and its combination
with HFI/HDI can control the PO pin output to make or break the line.
HKS=VDD: On-hook state (PO=low). Except for HFI/HDI
(hand-free/hold-linecontrolinput),otherfunctionsarealldisabled.
HKS=VSS: Off-hook state (PO=high). The chip is in the standby mode and
ready to receive the key input.
PO
O
CMOS OUT
This pin is a CMOS output structure, which by receiving HKS and HFO/HDO
signals, control the dialer to connect or disconnect the telephone line.
PO outputs a low to break the line when HKS is high (on-hook) and HFO/HDO
is low. PO outputs a high to make the line when HKS is low (off-hook) or HFO is
high or HDO is high.
During the off-hook state, the pin also outputs the dialing pulse train in pulse
mode dialing. While in the tone mode, this pin is always high.
MODE
I/O
CMOS IN/OUT
This is a three-state input/output pin, used for dialing mode selection whether
Tone mode or Pulse mode; 10pps/20pps.
MODE=VDD: Pulse mode, 10pps
MODE=OPEN: Pulse mode, 20pps
MODE=VSS: Tone mode
During pulse mode dialing, switching this pin to the tone mode changes the
subsequent digit entry to tone mode. When the chips are in tone mode, switch-
ing to the pulse mode will also be recognized.
HT9302 Series
Rev. 1.20
3
September 30, 2002
+
2
5 $ (
,
/
3
0
-
.
1
6
+
-
,
+
,
-
+
2
5 $ (
,
/
3
0
-
.
1
6
+
-
,
,
-
相關PDF資料 |
PDF描述 |
|---|---|
| HT9312 | 12-Memory Tone/Pulse Dialer |
| HT9312A | 12-Memory Tone/Pulse Dialer |
| HT9313C | 12-Memory Tone/Pulse Dialer |
| HT9313D | 12-Memory Tone/Pulse Dialer |
| HT9312CIT | 12-Memory Tone/Pulse Dialer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT9302H | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Pulse Telephone Dialer |
| HT9302X | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:1-Memory/2-Memory Tone/Pulse Dialer |
| HT9305A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Pulse Telephone Dialer |
| HT9305AI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Pulse Telephone Dialer |
| HT9305AIT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Pulse Telephone Dialer |
發布緊急采購，3分鐘左右您將得到回復。