- 您現在的位置：買賣IC網 > PDF目錄385404 > HT82K95A (Holtek Semiconductor Inc.) USB Multimedia Keyboard Encoder 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT82K95A |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | USB Multimedia Keyboard Encoder 8-Bit MCU |
| 中文描述： | 的USB多媒體鍵盤編碼器8位微控制器 |
| 文件頁數： | 12/48頁 |
| 文件大?。?/td> | 319K |
| 代理商： | HT82K95A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
HT82K95E/HT82K95A
Rev. 1.20
12
October 24, 2005
WS2
WS1
WS0
Division Ratio
0
0
0
1:1
0
0
1
1:2
0
1
0
1:4
0
1
1
1:8
1
0
0
1:16
1
0
1
1:32
1
1
0
1:64
1
1
1
1:128
WDTS (09H) Register
The WDT overflow under normal operation will initialize
a chip reset and set the status bit TO . But in the
HALT mode, the overflow will initialize a warm reset
and only the Program Counter and SP are reset to zero.
To clear the contents of the WDT (including the WDT
prescaler), three methods are employed; external reset
(a low level to RES), software instruction and a HALT
instruction. The software instruction include
CLR
WDT
and the other set
CLR WDT1
and
CLR
WDT2 . Of these two types of instruction, only one can
be active depending on the ROM code option
CLR
WDT times selection option . If the CLR WDT is se-
lected (i.e. CLRWDT times equal one), any execution of
the CLR WDT instruction will clear the WDT. In the
case wherein CLR WDT1 and CLR WDT2 are cho-
sen (i.e. CLRWDT times is equal to two), these two in-
structions must be executed to clear the WDT,
otherwise, the WDT may reset the chip as a result of
time-out.
Power Down Operation
HALT
The HALT mode is initialized by the HALT instruction
and results in the following:
The system oscillator will be turned off but the WDT
oscillator remains running (if the WDT oscillator is se-
lected).
The contents of the on-chip RAM and registers remain
unchanged.
WDT and WDT prescaler will be cleared and re-
counted again (if the WDT clock is from the WDT os-
cillator).
All of the I/O ports maintain their original status.
The PDF flag is set and the TO flag is cleared.
The system can leave the HALT mode by means of an
external reset, an interrupt, an external falling edge sig-
nal on I/O ports or a WDT overflow. An external reset
causes a device initialization and the WDToverflow per-
forms a warm reset . After the TO and PDF flags are
examined, the cause for chip reset can be determined.
The PDF flag is cleared by a system power-up or exe-
cuting the CLR WDT instruction and is set when exe-
cuting the HALT instruction. The TO flag is set if the
WDT time-out occurs, and causes a wake-up that only
resets the Program Counter and SP, the others remain
in their original status.
The I/O ports wake-up and interrupt methods can be
considered as a continuation of normal execution. Each
bit in the Port A can be independently selected to wake
up the device by option. PB, PC and PD can also be se-
lected to wake up the device by option. Upon awakening
from an I/O port stimulus, the program will resume exe-
cution of the next instruction. If it awakens from an inter-
rupt, two sequence may occur. If the related interrupt is
disabled or the interrupt is enabled but the stack is full,
the program will resume execution at the next instruc-
tion. If the interrupt is enabled and the stack is not full,
the regular interrupt response takes place. If an interrupt
requestflagissetto 1 beforeenteringtheHALTmode,
the wake-up function of the related interrupt will be dis-
abled. Once a wake-up event occurs, it takes 1024 t
SYS
(system clock period) to resume normal operation. In
other words, a dummy period will be inserted after a
wake-up. If the wake-up results from an interrupt ac-
knowledge signal, the actual interrupt subroutine execu-
tionwillbedelayedbyoneormorecycles.Ifthewakeup
results in the next instruction execution, this will be exe-
cutedimmediatelyafterthedummyperiodiscompleted.
To minimize power consumption, all the I/O pins should
be carefully managed before entering the HALT status.
Reset
Therearethreewaysinwhicharesetcanoccur:
RES reset during normal operation
RES reset during HALT
WDT time-out reset during normal operation
The WDT time-out during HALT is different from other
chip reset conditions, since it can perform a warm re -
set that resets only the Program Counter and SP, leav-
ing the other circuits in their original state. Some regis-
ters remain unchanged during other reset conditions.
Most registers are reset to the initial condition when
the reset conditions are met. By examining the PDF and
TO flags, the program can distinguish between different
chip resets .
TO PDF
RESET Conditions
0
0
RES reset during power-up
u
u
RES reset during normal operation
0
1
RES wake-up HALT
1
u
WDT time-out during normal operation
1
1
WDT wake-up HALT
Note: u stands for unchanged
To guarantee that the system oscillator is started and
stabilized, the SST (System Start-up Timer) provides an
相關PDF資料 |
PDF描述 |
|---|---|
| HT82K95E | USB Multimedia Keyboard Encoder 8-Bit MCU |
| HT82K96A | USB Multimedia Keyboard Encoder 8-Bit Mask MCU |
| HT82K96E | 8-Bit USB Multimedia Keyboard Encoder OTP MCU |
| HT82M21A | 3-Key 3D USB+PS/2 Optical Mouse Controller |
| HT82M22 | 5-Key 3D USB+PS/2 Optical Mouse Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT82K95AE | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit MCU |
| HT82K95E | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit MCU |
| HT82K95EE | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit MCU |
| HT82K96A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit Mask MCU |
| HT82K96E | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit USB Multimedia Keyboard Encoder OTP MCU |
發布緊急采購，3分鐘左右您將得到回復。