- 您現在的位置：買賣IC網 > PDF目錄385399 > HT48R70A-1 (Holtek Semiconductor Inc.) I/O Type 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT48R70A-1 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | I/O Type 8-Bit MCU |
| 中文描述： | I / O型8位微控制器 |
| 文件頁數： | 17/40頁 |
| 文件大?。?/td> | 273K |
| 代理商： | HT48R70A-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
HT48R70A-1/HT48C70-1
Rev. 1.60
17
June 9, 2004
lower-order byte buffer, respectively. Reading the
TMR1L will read the contents of the lower-order byte
buffer. The TMR1C is the Timer/Event Counter 1 control
register, which defines the operating mode, counting
enable or disable and active edge.
The T0M0, T0M1 (TMR0C), T1M0, T1M1 (TMR1C) bits
define the operating mode. The event count mode is
used to count external events, which means the clock
source comes from an external (TMR0/TMR1) pin. The
timer mode functions as a normal timer with the clock
source coming from the instruction clock or RTC clock
(Timer0/Timer1). The pulse width measurement mode
can be used to count the high or low level duration of the
external signal (TMR0/TMR1). The counting is based on
the instruction clock or RTC clock (Timer0/Timer1).
In the event count or timer mode, once the Timer/Event
Counter 0/1 starts counting, it will count from the current
contents in the Timer/Event Counter 0/1 to FFFFH.
Once overflow occurs, the counter is reloaded from the
Timer/Event Counter 0/1 preload register and generates
the interrupt request flag (T0F/T1F; bit 5/6 of INTC) at
the same time.
In the pulse width measurement mode with the
T0ON/T1ON and T0E/T1E bits equal to one, once the
TMR0/TMR1 has received a transient from low to high
(or high to low if the T0E/T1E bits is 0 ) it will start
counting until the TMR0/TMR1 returns to the original
level and resets the T0ON/T1ON. The measured result
will remain in the Timer/Event Counter 0/1 even if the
activated transient occurs again. In other words, only
one cycle measurement can be done. Until setting the
T0ON/T1ON, the cycle measurement will function again
as long as it receives further transient pulse. Note that,
in this operating mode, the Timer/Event Counter 0/1
starts counting not according to the logic level but ac-
cording to the transient edges. In the case of counter
overflows, the counter 0/1 is reloaded from the
Timer/Event Counter0/1 preloadregister and issues the
interrupt request just like the other two modes. To en-
able the counting operation, the timer ON bit (T0ON: bit
4 of TMR0C; T1ON: bit 4 of TMR1C) should be set to 1.
In the pulse width measurement mode, the T0ON/T1ON
will be cleared automatically after the measurement cy-
cle is completed. But in the other two modes the
T0ON/T1ON can only be reset by instructions. The
overflow of the Timer/Event Counter 0/1 is one of the
wake-up sources. No matter what the operation mode
is, writing a 0 to ET0I/ET1I can disable the correspond-
ing interrupt services.
In the case of Timer/Event Counter 0/1 OFF condition,
writing data to the Timer/Event Counter 0/1 preload
register will also reload that data to the Timer/Event
Counter 0/1. But if the Timer/Event Counter 0/1 is turned
on, data written to it will only be kept in the Timer/Event
Counter 0/1 preload register. The Timer/Event Counter
0/1 will still operate until overflow occurs (a Timer/Event
Counter 0/1 reloading will occur at the same time). When
the Timer/Event Counter 0/1 (reading TMR0/TMR1) is
read, the clock will be blocked to avoid errors. As clock
blocking may results in a counting error, this must be
taken into consideration by the programmer.
) !
( '
" $
!
"
(
)
2 ( -
!
*
(
)
" (
!
( -
!
)
"
% ) A
(
%
/
* 0
%
2 ( -
!
*
(
7
. *
# 9
#
A ( -
% %
-
Timer/Event Counter 1
) !
( '
" $
!
"
(
)
2 ( -
!
*
(
)
" (
!
( -
!
)
"
% ) A
(
%
/
* 0
%
2 ( -
!
*
(
7
. *
# 9
#
A ( -
% %
-
Timer/Event Counter 0
相關PDF資料 |
PDF描述 |
|---|---|
| HT48C70 | 8-Bit Microcontroller Series |
| HT48CA0-2 | Remote Type 8-Bit MCU |
| HT48RA0 | Remote Type 8-Bit MCU |
| HT48RA0-2 | Remote Type 8-Bit MCU |
| HT48CA0 | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT48R70A-1_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O Type 8-Bit MCU |
| HT48RA0 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Remote Type 8-Bit MCU |
| HT48RA0(20DIP-A) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| HT48RA0(20SOIC-A) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| HT48RA0(24SOIC-A) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。