- 您現在的位置：買賣IC網 > PDF目錄385400 > HT48CA0-2 (Holtek Semiconductor Inc.) Remote Type 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT48CA0-2 |
| 廠商： | Holtek Semiconductor Inc. |
| 元件分類： | 微控制器 |
| 英文描述： | Remote Type 8-Bit MCU |
| 中文描述： | 遠程型8位微控制器 |
| 文件頁數： | 6/32頁 |
| 文件大?。?/td> | 238K |
| 代理商： | HT48CA0-2 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
HT48RA0-2/HT48CA0-2
Rev. 1.50
6
July 23, 2004
Arithmetic and Logic Unit
ALU
This circuit performs 8-bit arithmetic and logic operation.
The ALU provides the following functions.
Arithmetic operations (ADD, ADC, SUB, SBC, DAA)
Logic operations (AND, OR, XOR, CPL)
Rotation (RL, RR, RLC, RRC)
Increment and Decrement (INC, DEC)
Branch decision (SZ, SNZ, SIZ, SDZ ....)
The ALU not only saves the results of a data operation but
also changes the contents of the status register.
Status Register
STATUS
This 8-bit status register (0AH) contains the zero flag
(Z), carry flag (C), auxiliary carry flag (AC), overflow flag
(OV), power down flag (PDF) and watchdog time-out
flag (TO). It also records the status information and con-
trols the operation sequence.
With the exception of the TO and PDF flags, bits in the
status register can be altered by instructions like most
other register. Any data written into the status register
will not change the TO or PDF flags. In addition it should
be noted that operations related to the status register
may give different results from those intended. The TO
and PDF flags can only be changed by the Watchdog
Timer overflow, chip power-up, clearing the Watchdog
Timer and executing the HALT instruction.
The Z, OV, AC and C flags generally reflect the status of
the latest operations.
In addition, on executing the subroutine call, the status
register will not be automatically pushed onto the stack.
If the contents of the status are important and if the sub-
routine can corrupt the status register, precautions must
be taken to save it properly.
Oscillator Configuration
There are two oscillator circuits implemented in the
microcontroller.
Both are designed for system clocks; the RC oscillator
and the Crystal oscillator, which are determined by code
options. No matter what oscillator type is selected, the
signal provides the system clock. The HALTmode stops
the system oscillator and ignores the external signal to
conserve power.
If an RC oscillator is used, an external resistor between
OSC1 and VSS in needed and the resistance must
range from 51k
4, is available on OSC2, which can be used to synchro-
nize external logic. The RC oscillator provides the most
cost effective solution. However, the frequency of the
oscillation may vary with V
DD
, temperature and the chip
itself due to process variations. It is, therefore, not suit-
able for timing sensitive operations where accurate os-
cillator frequency is desired.
to 1M . The system clock, divided by
If the Crystal oscillator is used, a crystal across OSC1
and OSC2 is needed to provide the feedback and phase
shift for the oscillator. No other external components are
needed. Instead of a crystal, the resonator can also be
connected between OSC1 and OSC2 to get a frequency
reference, but two external capacitors in OSC1 and
OSC2 are required.
Labels
Bits
Function
C
0
C is set if the operation results in a carry during an addition operation or if a borrow does not
take place during a subtraction operation; otherwise C is cleared. C is also affected by a rotate
through carry instruction.
AC
1
AC is set if the operation results in a carry out of the low nibbles in addition or no borrow from
the high nibble into the low nibble in subtraction; otherwise AC is cleared.
Z
2
Z is set if the result of an arithmetic or logic operation is zero; otherwise Z is cleared.
OV
3
OV is set if the operation results in a carry into the highest-order bit but not a carry out of the
highest-order bit, or vice versa; otherwise OV is cleared.
PDF
4
PDF is cleared when either a system power-up or executing the CLR WDT instruction. PDF is
set by executing the HALT instruction.
TO
5
TO is cleared by a system power-up or executing the CLR WDT or HALT instruction. TO is set
by a WDT time-out.
6~7
Unused bit, read as 0
Status Register
1 #
1 1
#
1 1
"
'
) *
7 6
#
#
8
System Oscillator
相關PDF資料 |
PDF描述 |
|---|---|
| HT48RA0 | Remote Type 8-Bit MCU |
| HT48RA0-2 | Remote Type 8-Bit MCU |
| HT48CA0 | 8-BIT MICROCONTROLLER |
| HT48CA1 | Remote Type 8-Bit MCU |
| HT48RA1 | Remote Type 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT48CA0-20DIP-A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| HT48CA0-3 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Remote Type 8-Bit MCU |
| HT48CA1 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Remote Type 8-Bit MCU |
| HT48CA3 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Remote Type 8-Bit MCU |
| HT48CA5 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Remote Type 8-Bit MCU |
發布緊急采購，3分鐘左右您將得到回復。