- 您現在的位置：買賣IC網 > PDF目錄385399 > HT46C65-52 (Holtek Semiconductor Inc.) A/D with LCD Type 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT46C65-52 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | A/D with LCD Type 8-Bit MCU |
| 中文描述： | 在A / D液晶型8位微控制器 |
| 文件頁數： | 13/48頁 |
| 文件大?。?/td> | 409K |
| 代理商： | HT46C65-52 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
HT46R65/HT46C65
Rev. 1.80
13
July 14, 2005
On the other hand, if the crystal oscillator is selected, a
crystalacrossOSC1andOSC2isneededtoprovidethe
feedback and phase shift required for the oscillator, and
no other external components are required. Aresonator
may be connected between OSC1 and OSC2 to replace
the crystal and to get a frequency reference, but two ex-
ternal capacitors in OSC1 and OSC2 are required.
There is another oscillator circuit designed for the real
time clock. In this case, only the 32.768kHz crystal oscil-
lator can be applied. The crystal should be connected
between OSC3 and OSC4.
The RTC oscillator circuit can be controlled to oscillate
quickly by setting the QOSC bit (bit 4 of RTCC). It is
recommended to turn on the quick oscillating function
upon power on, and then turn it off after 2 seconds.
The WDT oscillator is a free running on-chip RC oscilla-
tor, and no external components are required. Although
the system enters the power down mode, the system
clock stops, and the WDT oscillator still works with a pe-
riod of approximately 65 s at 5V. The WDT oscillator
can be disabled by options to conserve power.
Watchdog Timer
WDT
The WDT clock source is implemented by a dedicated
RC oscillator (WDT oscillator) or an instruction clock
(system clock/4) or a real time clock oscillator (RTC os-
cillator). The timer is designed to prevent a software
malfunction or sequence from jumping to an unknown
location with unpredictable results. The WDT can be
disabled by options. But if the WDT is disabled, all exe-
cutions related to the WDT lead to no operation.
Once an internal WDT oscillator (RC oscillator with pe-
riod 65 s at 5V normally) is selected, it is divided by
2
12
~2
15
(by ROM code option to get the WDT time-out
period). The minimum period of WDT time-out period is
about 300ms~600ms. This time-out period may vary
with temperature, VDD and process variations. By se-
lection the WDT ROM code option, longer time-out peri-
ods can be realized. If the WDT time-out is selected 2
15
,
themaximumtime-outperiodisdividedby2
15
~2
16
about
2.1s~4.3s. If the WDT oscillator is disabled, the WDT
clock may still come from the instruction clock and oper-
ate in the same manner except that in the halt state the
WDTmay stop counting and lose its protecting purpose.
In this situation the logic can only be restarted by exter-
nal logic. If the device operates in a noisy environment,
using the on-chip RC oscillator (WDT OSC) is strongly
recommended, since the HALT will stop the system
clock.
The WDT overflow under normal operation initializes a
chip reset and sets the status bit TO . In the HALT
mode, the overflow initializes a warm reset , and only
the program counter and SP are reset to zero. To clear
the contents of the WDT, there are three methods to be
adopted, i.e., external reset (a low level to RES), soft-
ware instruction, and a HALT instruction. There are
two types of software instructions; CLR WDT and the
other set
two types of instruction, only one type of instruction can
CLR WDT1 and CLR WDT2 . Of these
be active at a time depending on the options
CLR
WDT times selection option. If the CLR WDT is se-
lected (i.e., CLR WDT times equal one), any execution
of the CLR WDT instruction clears the WDT. In the
case that CLR WDT1 and CLR WDT2 are chosen
(i.e., CLR WDT times equal two), these two instructions
have to be executed to clear the WDT; otherwise, the
WDT may reset the chip due to time-out.
Multi-function Timer
The HT46R65/HT46C65 provides a multi-function timer
for the WDT, time base and RTC but with different
time-out periods. The multi-function timer consists of an
8-stage divider and a 7-bit prescaler, with the clock
source coming from the WDT OSC or RTC OSC or the
instruction clock (i.e., system clock divided by 4). The
multi-function timer also provides a selectable fre-
quency signal (ranges from f
S
/2
2
to f
S
/2
8
) for LCD driver
circuits, and a selectable frequency signal (ranging from
f
S
/2
2
to f
S
/2
9
) for the buzzer output by options. It is rec-
ommended to select a nearly 4kHz signal for the LCD
driver circuits to have proper display.
Time Base
The time base offers a periodic time-out period to gener-
ate a regular internal interrupt. Its time-out period
ranges from 2
12
/f
S
to 2
15
/f
S
selected by options. If time
base time-out occurs, the related interrupt request flag
(TBF; bit 5 of INTC1) is set. But if the interrupt is en-
abled, and the stack is not full, a subroutine call to loca-
tion 14H occurs.
7
)
3
- & ,
2
- &
- & ,
3
- &
- & ,
- &
- & ,
- &
#
)
1
-
8
(
)
1
(
9 :
4 2 6 9 :
*
*
&
(
1
)
& -
6
Watchdog Timer
相關PDF資料 |
PDF描述 |
|---|---|
| HT46C65-56 | A/D with LCD Type 8-Bit MCU |
| HT46R65 | A/D with LCD Type 8-Bit MCU |
| HT46R65-52 | A/D with LCD Type 8-Bit MCU |
| HT46R65-56 | A/D with LCD Type 8-Bit MCU |
| HT47C20L | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT46C65-56 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D with LCD Type 8-Bit MCU |
| HT46CU25 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU |
| HT46CU26 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU with UART |
| HT46CU66 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU with LCD |
| HT46CU66_11 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:A/D Type 8-Bit MCU with LCD |
發布緊急采購，3分鐘左右您將得到回復。