- 您現在的位置：買賣IC網 > PDF目錄385398 > HT27LC040 (Holtek Semiconductor Inc.) CMOS 512K 8-Bit OTP EPROM PDF資料下載
參數資料
| 型號： | HT27LC040 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | CMOS 512K 8-Bit OTP EPROM |
| 中文描述： | 為512k的CMOS 8位檢察官辦公室存儲器 |
| 文件頁數： | 5/15頁 |
| 文件大?。?/td> | 175K |
| 代理商： | HT27LC040 |
HT27LC040
Rev. 1.30
5
December 8, 2003
Program Verify Mode
Verification should be performed on the programmed
bits to determine whether they were correctly pro-
grammed. The verification should be performed with OE
at V
IL
, and CE at V
IH
, and VPP at its programming volt-
age.
Auto Product Identification
The Auto Product Identification mode allows the reading
out of a binary code from an EPROM that will identify its
manufacturer and the type. This mode is intended for
programming to automatically match the device to be
programmed with its corresponding programming algo-
rithm. This mode is functional in the 25 C 5 C ambient
temperature range that is required when programming
the HT27LC040.
To activate this mode, the programming equipment
must force 12.0 0.5V on the address line A9 of the
HT27LC040. Two identifier bytes may then be se-
quenced from the device outputs by toggling address
line A0 from V
IL
to V
IH
, when A1=V
IH
. All other address
lines must be held at V
IH
during Auto Product Identifica-
tion mode.
Byte 0 (A0=V
IL
) represents the manufacturer code, and
byte 1 (A0=V
IH
), the device code. For HT27LC040,
these two identifier bytes are given in the Operation
mode truth table. When A1=V
IL,
the HT27LC040 will
read out the binary code of 7F, continuation code, to sig-
nify the unavailability of manufacturer ID codes.
Read Mode
The has two control functions, both of which must be
logically satisfied in order to obtain data at outputs. Chip
Enable (CE) is the power control and should be used for
device selection. Output Enable (OE) is the output con-
trol and should be used to gate data to the output pins,
independent of device selection. Assuming that ad-
dresses are stable, address access time (t
ACC
) is equal
to the delay from CE to output (t
CE
). Data is available at
the outputs (t
OE
) after the falling edge of OE, assuming
the CE has been LOW and addresses have been stable
for at least t
ACC
-t
OE
.
Standby Mode
The HT27LC040 has CMOS standby mode which re-
duces the maximum VCC current to 10 A. It is placed in
CMOS standby when CE is at V
CC
0.3V. The
HT27LC040 also has a TTL-standby mode which re-
duces the maximum VCC current to 0.6mA. It is placed
in TTL-standby when CE is at V
IH
. When in standby
mode, the outputs are in a high-impedance state, inde-
pendent of the OE input.
Two-line Output Control Function
To accommodate multiple memory connections, a
two-line control function is provided to allow for:
Low memory power dissipation
Assurance that output bus contention will not occur
It is recommended that CE be decoded and used as the
primary device-selection function, while OE be made a
common connection to the READ line from the system
control bus. This assures that all deselected memory
devices are in their low-power standby mode and that
the output pins are only active when data is desired from
a particular memory device.
System Considerations
During the switch between active and standby condi-
tions, transient current peaks are produced on the rising
and falling edges of Chip Enable. The magnitude of
these transient current peaks is dependent on the out-
put capacitance loading of the device. At a minimum, a
0.1 F ceramic capacitor (high frequency, low inherent
inductance) should be used on each device between
VCC and VPP to minimize transient effects. In addition,
to overcome the voltage drop caused by the inductive
effects of the printed circuit board traces on EPROM ar-
rays, a 4.7 F bulk electrolytic capacitor should be used
between VCC and VPP for each eight devices. The lo-
cation of the capacitor should be close to where the
power supply is connected to the array.
相關PDF資料 |
PDF描述 |
|---|---|
| HT27LC512 | OTP CMOS 64Kx 8-Bit EPROM |
| HT2812 | Single Sound Generator |
| HT2812-14DIP | Single Sound Generator |
| HT2812-8DIP | Single Sound Generator |
| HT2812A | Single Sound Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT27LC4096 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMOS 256K?16-Bit OTP EPROM ??(3.3V) |
| HT27LC512 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:OTP CMOS 64Kx 8-Bit EPROM |
| HT27LC512(28DIP) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM |
| HT27LC512(28SOP) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM |
| HT27LC512(32PLCC) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM |
發布緊急采購，3分鐘左右您將得到回復。