![](http://datasheet.mmic.net.cn/Intersil/HSP45102SC-40Z_datasheet_101083/HSP45102SC-40Z_6.png)
6
FN2810.9
April 25, 2007
Absolute Maximum Ratings TA = +25°C
Thermal Information
Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +6.0V
Input, Output or I/O Voltage Applied . . . . .GND -0.5V to VCC +0.5V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Operating Conditions
Operating Voltage Range (Commercial, Industrial). . +4.75V to +5.25V
Operating Temperature Range (Commercial) . . . . . . . 0°C to +70°C
Operating Temperature Range (Industrial) . . . . . . . .-40°C to +85°C
Thermal Resistance (Typical, Note
1)θJA (°C/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . -65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
Die Characteristics
Backside Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1.
θ
JA is measured with the component mounted on an evaluation PC board in free air.
DC Electrical Specifications
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
MAX
UNITS
Logical One Input Voltage
VIH
VCC = 5.25V
2.0
-
V
Logical Zero Input Voltage
VIL
VCC = 4.75V
-
0.8
V
High Level Clock Input
VIHC
VCC = 5.25V
3.0
-
V
Low Level Clock Input
VILC
VCC = 4.75V
-
0.8
V
Output HIGH Voltage
VOH
IOH = -400μA, VCC = 4.75V
2.6
-
V
Output LOW Voltage
VOL
IOL = +2.0mA, VCC = 4.75V
-
0.4
V
Input Leakage Current
II
VIN = VCC or GND, VCC = 5.25V
-10
10
μA
Standby Power Supply Current
ICCSB
VIN = VCC or GND, VCC = 5.25V, Note 4 -
500
μA
Operating Power Supply Current
ICCOP
f = 33MHz, VIN = VCC or GND
VCC = 5.25V, Notes 2 and 4 -99
mA
Capacitance TA = +25°C, Note 3 PARAMETER
SYMBOL
TEST CONDITIONS
MIN
MAX
UNITS
Input Capacitance
CIN
FREQ = 1MHz, VCC = Open. All
measurements are referenced to device
ground
-10
pF
Output Capacitance
CO
-10
pF
NOTES:
2. Power supply current is proportional to operating frequency. Typical rating for ICCOP is 3mA/MHz.
3. Not tested, but characterized at initial design and at major process/design changes.
4. Output load per test load circuit with switch open and CL = 40pF.
HSP45102