- 您現在的位置：買賣IC網 > PDF目錄385394 > HSDL-3603-207 (Avago Technologies Ltd.) IrDA㈢ Data Compliant 4 Mbit/s Infrared Transceiver PDF資料下載
參數資料
| 型號： | HSDL-3603-207 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | IrDA㈢ Data Compliant 4 Mbit/s Infrared Transceiver |
| 中文描述： | 紅外線㈢數據符合4 Mbit / s的紅外收發器 |
| 文件頁數： | 14/29頁 |
| 文件大?。?/td> | 226K |
| 代理商： | HSDL-3603-207 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
14
Reflow Profile
The reflow profile is a straight-
line representation of a nominal
temperature profile for a convec-
tive reflow solder process. The
temperature profile is divided
into four process zones, each
with different
T/
time tempera-
ture change rates. The
T/
time
rates are detailed in the following
table. The temperatures are mea-
sured at the component to
printed circuit board connections.
In
process zone P1
, the PC
board and HSDL-3603
castellation I/O pins are heated
to a temperature of 125
°
C to
activate the flux in the solder
paste. The temperature ramp up
rate, R1, is limited to 4
°
C per
second to allow for even heating
of both the PC board and
HSDL-3603 castellation I/O pins.
Process zone P2
should be of
sufficient time duration (> 60
seconds) to dry the solder paste.
The temperature is raised to a
level just below the liquidus point
of the solder, usually 170
°
C
(338
°
F).
Process zone P3
is the solder
reflow zone. In zone P3, the
temperature is quickly raised
above the liquidus point of solder
to 230
°
C (446
°
F) for optimum
results. The dwell time above the
liquidus point of solder should be
between 15 and 90 seconds. It
usually takes about 15 seconds to
assure proper coalescing of the
solder balls into liquid solder and
the formation of good solder
0
t-TIME (SECONDS)
T
200
183
170
150
125
100
50
50
150
100
200
250
300
230
P1
HEAT
UP
P2
SOLDER PASTE DRY
P3
SOLDER
REFLOW
P4
COOL
DOWN
25
R1
R2
R3
R4
R5
90 sec.
MAX.
ABOVE
183°C
MAX. 245°C
Maximum
T/
time
4C/s
0.5C/s
4C/s
–4C/s
–3C/s
Process Zone
Heat Up
Solder Paste Dry
Solder Reflow
Symbol
P1, R1
P2, R2
P3, R3
P3, R4
P4, R5
T
25C to 125C
125C to 170C
170C to 230C (245C max.)
230C to 170C
170C to 25C
Cool Down
connections. Beyond a dwell time
of 90 seconds, the intermetallic
growth within the solder connec-
tions becomes excessive,
resulting in the formation of weak
and unreliable connections. The
temperature is then rapidly
reduced to a point below the
solidus temperature of the solder,
usually 170
°
C (338
°
F), to allow
the solder within the connections
to freeze solid.
Process zone P4
is the cool
down after solder freeze. The
cool down rate, R5, from the
liquidus point of the solder to
25
°
C (77
°
F) should not exceed
-3
°
C per second maximum. This
limitation is necessary to allow
the PC board and HSDL-3603
castellation I/O pins to change
dimensions evenly, putting
minimal stresses on the
HSDL-3603 transceiver.
Figure 17. Reflow graph.
相關PDF資料 |
PDF描述 |
|---|---|
| HSDL-3603-208 | IrDA㈢ Data Compliant 4 Mbit/s Infrared Transceiver |
| HSDL-4250 | High-Performance T-1 (5mm) AlGaAs Infrared (870nm) Lamp |
| HSDL-4251 | High-Performance T-1 (5mm) AlGaAs Infrared (870nm) Lamp |
| HSDL-4260 | High-Power T-1 (5mm) AlGaAs Infrared (875nm) Lamp |
| HSDL-4261 | High-Power T-1 (5mm) AlGaAs Infrared (870nm) Lamp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HSDL-3603-208 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:IrDA㈢ Data Compliant 4 Mbit/s Infrared Transceiver |
| HSDL-3610 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IrDA 1.0 Data Compliant 115.2Kb/s 3-5V Infrared Transceiver(not recommended for new designs) |
| HSDL-3610#007 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HSDL-3610#008 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HSDL-3610#017 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。