- 您現在的位置：買賣IC網 > PDF目錄384440 > HS7B-1100RH-Q (INTERSIL CORP) Radiation Hardened, Ultra High Speed Current Feedback Amplifier PDF資料下載
參數資料
| 型號： | HS7B-1100RH-Q |
| 廠商： | INTERSIL CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | Radiation Hardened, Ultra High Speed Current Feedback Amplifier |
| 中文描述： | VIDEO AMPLIFIER, CDIP8 |
| 封裝： | SIDE BRAZED, CERAMIC, DIP-8 |
| 文件頁數： | 2/11頁 |
| 文件大?。?/td> | 132K |
| 代理商： | HS7B-1100RH-Q |
2
Typical Applications
Optimum Feedback Resistor
The enclosed plots of inverting and non-inverting frequency
response illustrate the performance of the HS-1100RH in
various gains. Although the bandwidth dependency on
closed loop gain isn’t as severe as that of a voltage
feedback amplifier, there can be an appreciable decrease
in bandwidth at higher gains. This decrease may be
minimized by taking advantage of the current feedback
amplifier’s unique relationship between bandwidth and R
F
.
All current feedback amplifiers require a feedback resistor,
even for unity gain applications, and R
F
, in conjunction with
the internal compensation capacitor, sets the dominant
pole of the frequency response. Thus, the amplifier’s
bandwidth is inversely proportional to R
F
. The HS-1100RH
design is optimized for a 510
R
F
at a gain of +1.
Decreasing R
F
in a unity gain application decreases
stability, resulting in excessive peaking and overshoot. At
higher gains the amplifier is more stable, so R
F
can be
decreased in a trade-off of stability for bandwidth.
The table below lists recommended R
F
values for various
gains, and the expected bandwidth.
PC Board Layout
The frequency response of this amplifier depends greatly on
the amount of care taken in designing the PC board.
The
use of low inductance components such as chip
resistors and chip capacitors is strongly recommended,
while a solid ground plane is a must!
Attention should be given to decoupling the power supplies.
A large value (10
μ
F) tantalum in parallel with a small value
(0.1
μ
F) chip capacitor works well in most cases.
Terminated microstrip signal lines are recommended at the
input and output of the device. Capacitance directly on the
output must be minimized, or isolated as discussed in the
next section.
Care must also be taken to minimize the capacitance to
ground seen by the amplifier’s inverting input (-IN). The
larger this capacitance, the worse the gain peaking, resulting
in pulse overshoot and possible instability. To this end, it is
recommended that the ground plane be removed under
traces connected to -IN, and connections to -IN should be
kept as short as possible.
An example of a good high frequency layout is the
Evaluation Board shown in Figure 2.
Driving Capacitive Loads
Capacitive loads, such as an A/D input, or an improperly
terminated transmission line will degrade the amplifier’s
phase margin resulting in frequency response peaking and
possible oscillations. In most cases, the oscillation can be
avoided by placing a resistor (R
S
) in series with the output
prior to the capacitance.
Figure 1 details starting points for the selection of this
resistor. The points on the curve indicate the R
S
and C
L
combinations for the optimum bandwidth, stability, and
settling time, but experimental fine tuning is recommended.
Picking a point above or to the right of the curve yields an
overdamped response, while points below or left of the curve
indicate areas of underdamped performance.
R
S
and C
L
form a low pass network at the output, thus
limiting system bandwidth well below the amplifier bandwidth
of 850MHz. By decreasing R
S
as C
L
increases (as
illustrated in the curves), the maximum bandwidth is
obtained without sacrificing stability. Even so, bandwidth
does decrease as you move to the right along the curve. For
example, at A
V
= +1, R
S
= 50
, C
L
= 30pF, the overall
bandwidth is limited to 300MHz, and bandwidth drops to
100MHz at A
V
= +1, R
S
= 5
, C
L
= 340pF.
Evaluation Board
The performance of the HS-1100RH may be evaluated using
the HFA11XXEVAL Evaluation Board.
The layout and schematic of the board are shown in
Figure 2. To order evaluation boards, please contact your
local sales office.
GAIN
(ACL)
R
F
(
)
BANDWIDTH
(MHz)
-1
430
580
+1
510
850
+2
360
670
+5
150
520
+10
180
240
+19
270
125
R
S
)
LOAD CAPACITANCE (pF)
50
45
40
35
30
25
20
15
10
5
0
0
40
80
120
160
200
240
280
320
360 400
A
V
= +1
A
V
= +2
FIGURE 1. RECOMMENDED SERIES OUTPUT RESISTOR vs
LOAD CAPACITANCE
HS-1100RH
相關PDF資料 |
PDF描述 |
|---|---|
| HS-1115RH | Radiation Hardened, High Speed, Low Power Output Limiting, Closed-Loop-Buffer Amplifier(抗輻射高速、低功耗、輸出限定的鎖相環(huán)緩沖放大器) |
| HS-1120RH | Radiation Hardened, Ultra High Speed Current Feedback Amplifier with Offset Adjust(抗輻射超高速電流反饋放大器（可調節(jié)漂移）) |
| HS-1145RH | Radiation Hardened, High Speed, Low Power, Current Feedback Video Operational Amplifier with Output Disable(抗輻射超高速電流反饋視頻運算放大器（帶輸出禁止）) |
| HS7-1145RH-Q | CONNECTOR ACCESSORY |
| HS7B-1145RH-Q | Radiation Hardened, High Speed, Low Power, Current Feedback Video Operational Amplifier with Output Disable |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HS7B-1115RH-Q | 制造商:Intersil Corporation 功能描述:OP AMP SGL GP 5V 8CDIP - Bulk |
| HS7B-1135RH/PROTO | 制造商:Intersil Corporation 功能描述:RH UHF CURRENT FEEDBACK AMP W/VIO ADJUST,PROTOTYPE,CLS V - Bulk |
| HS7B-1135RH-Q | 制造商:Intersil Corporation 功能描述:OP AMP SGL CURRENT FDBK 5.53V 8CDIP - Bulk |
| HS7B-1145RH/PROTO | 制造商:Intersil Corporation 功能描述:RAD HARD, VIDEO OP-AMP WITH OUTPUT DISABLE, MINIDIP, PROTOTY - Bulk |
| HS7B-1145RH-Q | 制造商:Intersil Corporation 功能描述:OP AMP SGL CURRENT FDBK 6V 8PIN SBCDIP - Bulk |
發(fā)布緊急采購，3分鐘左右您將得到回復。