參數資料
型號: HMC6052
廠商: Electronic Theatre Controls, Inc.
英文描述: INTEGRATED COMPASS SENSOR
中文描述: 內置羅盤傳感器
文件頁數: 5/6頁
文件大?。?/td> 161K
代理商: HMC6052
HMC6052
www.honeywell.com
5
Reference Design
The schematic diagram in Figure 1 shows the basic HMC6052 application circuit with a minimum of external components.
Figure 1
From Figure 1, the host microprocessor (
μ
P) controls the HMC6052 via digital output port lines DO0 through DO2. The
first digital control line (DO0) is normally in a high logic state and briefly pulls down to drive the high-side switch connected
to pin 10 (SINH) of the HMC6052. Likewise, DO1 is a reverse logic control line that is normally low and pulls high briefly to
drive the low-side switch at pin 7 (SINL) of the HMC6052. Together DO0 and DO1 toggle states to create a “set” pulse
through the internal set strap resistance that spirals through the sensor bridge elements. This set pulse creates an intense
magnetic field that will re-align the magnetic domains of the magneto-resistive elements to undo the effects of thermal
agitation, and any magnetic upset events that might “disturb” the sensors. The frequency of the toggling is the designer’s
choice, but typically ranges from once per second to once per day. The external set strap capacitance across pins 5 (SC-)
and 9 (SC+) is to be around 0.2uf to 1uf in value, with emphasis on keeping the total capacitor ESR (effective series
resistance) below 0.5 ohms to minimize capacitor internal losses while delivering a current spike in excess of 0.5
amperes.
The microprocessor also has control of the complete power supplied to the HMC6052 via digital control line DO2 that
switches the MMBT2907 bipolar junction transistor, to connect the 3.0-volt system supply voltage to the sensor circuits.
By pulling low DO2, the transistor saturates to connect Vdd to Vdds, which are the switched supply connections to
VSUPPLY (pin 11) and VBRIDGE (pin 3). With power applied, the HMC6052 internal circuits quickly stabilize to provide
accurate magnetic vector voltages at output pins 13 (OUTA) and 14 (OUTB). With near zero magnetic field inputs, OUTA
and OUTB should be near half the supply voltage to provide bipolar output voltage values corresponding to the intensity
and polarity of the resulting magnetic fields on the sensor bridges. Zero field stimulus to the HMC6052 can be obtained
using magnetic shielded containers, or helmholtz coil sets.
Toggling the DO2 digital control line is necessary in many applications to reduce the total system current consumption
when not taking magnetic field measurements to preserve battery energy reserves. Up to 15mA can be drawn from the
G
G
AMR
AMR
SW
SW
SET
OFFSET
Vref
GND
GND
GND
GND
GND
V+
V+
V+
V+
V+
GND
GND
GND
SINL
SINH
SC+
SC-
OUTA
OUTB
OFF+
OFF-
VBRIDGE
Vdds = 3V
(2)
AN0
AN1
μ
P
Vss
GND
Vdd
MMBT2907
DO2
DO1
DO0
10k
TXD
CLK
GND
XTAL0
XTAL1
+3V
10
7
12
11
14
13
3
Vdds
4
1
5
9
RXD
I/O
NC
NC
GND
VSR
+
RS
8
6
S/R+
0.1
μ
F X7R
Vdd
SERIAL
1
μ
F X7R
相關PDF資料
PDF描述
HMDL2416TXV Optoelectronic
HMDL2416TXVB Optoelectronic
HMF2M32B4V Flash-ROM Module 8MByte (2Mx32Bit), 72Pin-SO-DIMM, 3.3V
HMF2M32B4V-120 Flash-ROM Module 8MByte (2Mx32Bit), 72Pin-SO-DIMM, 3.3V
HMF2M32B4V-70 Flash-ROM Module 8MByte (2Mx32Bit), 72Pin-SO-DIMM, 3.3V
相關代理商/技術參數
參數描述
HMC605LP3 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 2.3 - 2.7 GHz
HMC605LP3_09 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC LOW NOISE AMPLIFIER w/ BYPASS MODE, 2.3 - 2.7 GHz
HMC605LP3E 制造商:Hittite Microwave Corp 功能描述:IC MMIC AMP LNA BYPASS 16-QFN
HMC605LP3ETR 制造商:Hittite Microwave Corp 功能描述:HMC605 Series 2.3 - 2.7 GHz Low Noise Amplifier with Bypass - QFN-16
HMC606 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs InGaP HBT MMIC ULTRA LOW PHASE NOISE, DISTRIBUTED AMPLIFIER, 2 - 18 GHz