- 您現在的位置：買賣IC網 > PDF目錄367212 > HMC441 (美國訊泰微波有限公司上海代表處) 800000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN PDF資料下載
參數資料
| 型號： | HMC441 |
| 廠商： | 美國訊泰微波有限公司上海代表處 |
| 元件分類： | FPGA |
| 英文描述： | 800000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| 中文描述： | GaAs PHEMT MMIC中功率放大器，6.0 - 18.0千兆赫 |
| 文件頁數： | 8/8頁 |
| 文件大小： | 318K |
| 代理商： | HMC441 |
MICROWAVE CORPORATION
8 - 197
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
A
8
HMC441LM1
GaAs PHEMT MMIC MEDIUM
POWER AMPLIFIER, 7.0 - 15.5 GHz
v00.1202
Recommended SMT Attachment Technique
Preparation & Handling of the LM1 Microwave Package for Surface Mounting
The HMC LM1 package was designed to be compatible with high volume
surface mount PCB assembly processes. The LM1 package requires a
specific mounting pattern to allow proper mechanical attachment and to
optimize electrical performance at millimeterwave frequencies. This PCB
layout pattern can be found on each LM1 product data sheet. It can also
be provided as an electronic drawing upon request from Hittite Sales &
Application Engineering.
Follow these precautions to avoid permanent damage:
Cleanliness:
Observe proper handling procedures to ensure clean devices
and PCBs. LM1 devices should remain in their original packaging until
component placement to ensure no contamination or damage to RF, DC &
ground contact areas.
Static Sensitivity:
Follow ESD precautions to protect against ESD strikes.
General Handling:
Handle the LM1 package on the top with a vacuum collet or along the edges with a sharp pair of bent tweezers.
Avoiding damaging the RF, DC, & ground contacts on the package bottom. Do not apply excess pressure to the top of the lid.
Solder Materials & Temperature Profile:
Follow the information contained in the application note. Hand soldering is not recommended.
Conductive epoxy attachment is not recommended.
Solder Paste:
Solder paste should be selected based on the user’s experience and be compatible with the metallization systems used.
See the LM1 data sheet Outline drawing for pin & ground contact metallization schemes.
Solder Paste Application:
Solder paste is generally applied to the PCB using either a stencil printer or dot placement. The volume of
solder paste will be dependent on PCB and component layout and should be controlled to ensure consistent mechanical & electrical
performance. Excess solder may create unwanted electrical parasitics at high frequencies.
Solder Reflow:
The soldering process is usually accomplished in a reflow oven but may also use a vapor phase process. A solder
reflow profile is suggested above.
Prior to reflowing product, temperature profiles should be measured using the same mass as the actual assemblies. The thermocouple
should be moved to various positions on the board to account for edge and corner effects and varying component masses. The final
profile should be determined by mounting the thermocouple to the PCB at the location of the device.
Follow solder paste and oven vendor’s recommendations when developing a solder reflow profile. A standard profile will have a steady
ramp up from room temperature to the pre-heat temperature to avoid damage due to thermal shock. Allow enough time between
reaching pre-heat temperature and reflow for the solvent in the paste to evaporate and the flux to completely activate. Reflow must
then occur prior to the flux being completely driven off. The duration of peak reflow temperature should not exceed 15 seconds.
Packages have been qualified to withstand a peak temperature of 235°C for 15 seconds. Verify that the profile will not expose device
to temperatures in excess of 235°C.
Cleaning:
A water-based flux wash may be used.
25
50
75
100
125
150
175
200
225
0
1
2
3
4
5
6
7
8
T
0
C
TIME (min)
相關PDF資料 |
PDF描述 |
|---|---|
| HMC442LC3B | GaAs PHEMT MMIC MEDIUM POWER AMPLIFIER, 17.5 - 25.5 GHz |
| HMC442 | 800000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| HMC442LM1 | GaAs PHEMT MMIC MEDIUM POWER AMPLIFIER, 17.5 - 24 GHz |
| HMC443LP4 | SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 9.8 - 11.2 GHz OUTPUT |
| HMC444LP4 | SMT GaAs HBT MMIC x8 ACTIVE FREQUENCY MULTIPLIER, 9.9 - 11.2 GHz OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMC441_09 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC MEDIUM POWER AMPLIFIER, 6 - 18 GHz |
| HMC441LC3B | 功能描述:IC MMIC PWR AMP 3X3QFN RoHS:是 類別:RF/IF 和 RFID >> RF 放大器 系列:- 標準包裝:3,000 系列:- 頻率:100MHz ~ 6GHz P1dB:9.14dBm（8.2mW） 增益:15.7dB 噪音數據:1.3dB RF 型:CDMA，TDMA，PCS 電源電壓:2.7 V ~ 5 V 電流 - 電源:60mA 測試頻率:2GHz 封裝/外殼:0505（1412 公制） 包裝:帶卷 (TR) |
| HMC441LC3B_08 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC MEDIUM POWER AMPLIFIER, 6 - 18 GHz |
| HMC441LC3BTR | 制造商:Hittite Microwave Corp 功能描述:IC MMIC PWR AMP 3X3QFN |
| HMC441LH5 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC MEDIUM POWER AMPLIFIER, 7 - 15.5 GHz |
發布緊急采購，3分鐘左右您將得到回復。