- 您現在的位置：買賣IC網 > PDF目錄367208 > HMC283 (美國訊泰微波有限公司上海代表處) 600000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN PDF資料下載
參數資料
| 型號： | HMC283 |
| 廠商： | 美國訊泰微波有限公司上海代表處 |
| 元件分類： | FPGA |
| 英文描述： | 600000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| 中文描述： | 砷化鎵MMIC中功率放大器，17 - 40千兆赫 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 284K |
| 代理商： | HMC283 |
MICROWAVE CORPORATION
1 - 14
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
A
1
GaAs MMIC MEDIUM POWER
AMPLIFIER, 17 - 40 GHz
HMC283
v02.0500
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane
eutectically or with conductive epoxy (see HMC gen-
eral Handling, Mounting, Bonding Note.)
50 Ohm Microstrip transmission lines on 0.127 mm (5
mil) thick alumina thin film substrates are recom-
mended for bringing RF to and from the chip (Figure 1).
If 0.254 mm (10 mil) thick alumina thin film substrates
must be used, the die should be raised 0.150 mm (6
mils) so that the surface of the die is coplanar with the
surface of the substrate. One way to accomplish this is
to attach the 0.102 mm (4 mil) thick die to a 0.150 mm
(6 mil) thick molybdenum heat spreader (moly-tab)
which is then attached to the ground plane (Figure 2).
Microstrip substrates should be brought as close to the
die as possible in order to minimize bond wire length.
Typical die-to-substrate spacing is 0.076 mm (3 mils).
Gold ribbon of 0.076 mm x 0.013 mm (3 mil x 0.5 mil) is recommended to minimize inductance on the RF ports.
0.025 mm (1 mil) diameter ball or wedge bonds are acceptable for DC bias connections.
RF bypass capacitors should be used on the Vdd & Vgg inputs. 100 pF single layer capacitors (mounted eutecti-
cally or by conductive epoxy) placed no further than 0.762 mm (30 mils) from the chip are recommended. The
photo in figure 3 shows a typical assembly for the HMC283 MMIC chip.
Figure 3:
Typical HMC283 Assembly
相關PDF資料 |
PDF描述 |
|---|---|
| HMC283LM1 | SMT MEDIUM POWER GaAs MMIC AMPLIFIER, 17 - 40 GHz |
| HMC284MS8G | SPDT NON-REFLECTIVE SWITCH, DC - 3.5 GHz |
| HMC285 | 600000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| HMC286 | 600000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| HMC287MS8 | GaAs MMIC LOW NOISE AMPLIFIER with AGC, 2.3 - 2.5 GHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMC283_07 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC MEDIUM POWER AMPLIFIER, 17 - 40 GHz |
| HMC283_08 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC MEDIUM POWER AMPLIFIER, 17 - 40 GHz |
| HMC283_10 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC MEDIUM POWER AMPLIFIER, 17 - 40 GHz |
| HMC283LM1 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:SMT MEDIUM POWER GaAs MMIC AMPLIFIER, 17 - 40 GHz |
| HMC283LM1_01 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:SMT MEDIUM POWER GaAs MMIC AMPLIFIER, 17 - 40 GHz |
發布緊急采購，3分鐘左右您將得到回復。