- 您現在的位置：買賣IC網 > PDF目錄367208 > HMC247_08 (美國訊泰微波有限公司上海代表處) 400∑ ANALOG PHASE SHIFTER 5 - 18 GHz PDF資料下載
參數資料
| 型號： | HMC247_08 |
| 廠商： | 美國訊泰微波有限公司上海代表處 |
| 英文描述： | 400∑ ANALOG PHASE SHIFTER 5 - 18 GHz |
| 中文描述： | 400Σ模擬移相器5 - 18千兆赫 |
| 文件頁數： | 6/6頁 |
| 文件大?。?/td> | 242K |
| 代理商： | HMC247_08 |
3
3 - 7
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage:
All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag
for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment.
Cleanliness:
Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems.
Static Sensitivity:
Follow ESD precautions to protect against ESD strikes.
Transients:
Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize
inductive pick-up.
General Handling:
Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the
chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with electrically conductive epoxy. The mounting surface should be clean
and flat.
Epoxy Die Attach:
Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of
150 deg. C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum
level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or
substrate. All bonds should be as short as possible <0.31mm (12 mils).
Outline Drawing
1. ALL DIMENSIONS ARE IN INCHES [MM]
2. TIE ALL UNLABLED BOND PADS TO GROUND.
3. DIE THICKNESS IS .004”
4. TYPICAL BOND PAD IS .004” SQUARE.
5. BACKSIDE METALIZATION: GOLD.
6. BOND PAD METALIZATION: GOLD.
HMC247
v01.1007
400° ANALOG PHASE SHIFTER
5 - 18 GHz
相關PDF資料 |
PDF描述 |
|---|---|
| HMC247 | 400∑ ANALOG PHASE SHIFTER 5 - 18 GHz |
| HMC251MS8 | GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz |
| HMC252QS24 | GaAs MMIC SP6T NON-REFLECTIVE SWITCH, DC - 3.0 GHz |
| HMC253LC4 | GaAs MMIC SP8T NON-REFLECTIVE SWITCH, DC - 3.5 GHz |
| HMC253QS24 | GaAs MMIC SP8T NON-REFLECTIVE SWITCH, DC - 2.5 GHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMC247-SX | 功能描述:IC PHASE SHIFTER DIE 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 功能:相移 頻率:5GHz ~ 18GHz RF 類型:通用 輔助屬性:- 封裝/外殼:模具 供應商器件封裝:模具 標準包裝:2 |
| HMC2512JT20M0 | 制造商:SEI Stackpole Electronics Inc 功能描述:RES THKFLM 2512 20M OHM 5% 1W 200PPM/ C SMD - Tape and Reel |
| HMC251MS8 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz |
| HMC251MS8_01 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz |
| HMC251MS8_10 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC SMT DIVIDE-BY-2, 3.0 - 6.5 GHz |
發布緊急采購，3分鐘左右您將得到回復。