- 您現在的位置：買賣IC網 > PDF目錄384423 > HIP9021 (Intersil Corporation) Portable Battery Drive/Torque Controller for N-Channel MOSFETs in Motor Control Systems PDF資料下載
參數資料
| 型號： | HIP9021 |
| 廠商： | Intersil Corporation |
| 英文描述： | Portable Battery Drive/Torque Controller for N-Channel MOSFETs in Motor Control Systems |
| 中文描述： | 便攜式電池驅動/力矩控制器N通道在電機控制系統的MOSFET |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 59K |
| 代理商： | HIP9021 |
5
Pin Descriptions
NAME
NUMBER
DESCRIPTION
DRAIN
1
The input to the DRAIN pin senses the drain of a power MOSFET Output Motor Driver. The DRAIN volt-
age is an image of the current flowing through the power MOSFET. By limiting this voltage, the torque of
the motor can be controlled.
TRIGGER
2
The TRIGGER input is an analog voltage control level used to fix the duty-cycle at the DRAIN Output. A
voltage level here is determined by a potentiometer adjustment. The TRIGGER voltage level is com-
pared with the triangle signal from the internal oscillator to produce a pulse-width modulated signal.
GND
3
Negative pole of the battery or system ground reference.
OSC
4
Oscillator output normally terminated in a charge/discharge capacitor. A constant current is flowing in
and out to charge and discharge the external capacitor.
TORQUE
5
The TORQUE input is a reference level adjustment for torque control. The voltage reference is compared
with DRAIN input. If V
DRAIN
> V
TORQUE
, the GATE output pulse drive must be disabled.
DELAY
6
An external capacitor at the DELAY output is used to delay the torque control action. The external ca-
pacitor at the DELAY pin will start to be charged if a MOSFET output over-current condition is detected.
The purpose of the capacitor is to delay the disabling action of the signal GATE drive.
GATE
7
The GATE output drives the Gate of the Power MOSFET.
V
DD
8
Positive pole of the battery or Power Supply Voltage, nominally 7.5V.
+
NOTE: The value chosen for the torque level set pot is dependent on the type of power MOSFET and motor characteristics.
The TRIGGER is a combined SW/Speed Control function. Motor speed increases as the TRIGGER voltage decreases.
Speed control range: 2.35V (Min) < V
TRIGGER
< 5.25V (Max)
FIGURE 2. TYPICAL OPERATING CIRCUIT SHOWING THE HIP9021IB AS AN N-CHANNEL MOSFET DRIVER IN A PORTABLE
BATTERY ELECTRIC DRILL APPLICATION
1nF
3.3
μ
F
PORTABLE
ELECTRIC
DRILL MOTOR
OSCILLATOR
CONTROL
&
LOGIC
DRAIN
TRIGGER
GATE
TORQUE
OSC
DELAY
HIP9021
V
DD
GND
TORQUE
LEVEL SET
SPEED
CONTROL
V
BATT
GC
+
1nF
180K
5.6K
100K
470K
200K
270K
1
μ
F
7.5V
330
15K
RFP45N03L
N-CHANNEL
SW
POWER
MOSFET
+
-
HIP9021
相關PDF資料 |
PDF描述 |
|---|---|
| HIP9021IB | Portable Battery Drive/Torque Controller for N-Channel MOSFETs in Motor Control Systems |
| HIP9022 | Dual High Speed Laser Driver |
| HIP9022AM | Dual High Speed Laser Driver |
| HIRF740 | N-Channel Power MOSFET (400V, 10A) |
| HIRF740F | N-Channel Power MOSFET (400V, 10A) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP9021IB | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Portable Battery Drive/Torque Controller for N-Channel MOSFETs in Motor Control Systems |
| HIP9022 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual High Speed Laser Driver |
| HIP9022AM | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual High Speed Laser Driver |
| HIPC6100 | 制造商:Hubbell Wiring Device-Kellems 功能描述:CABLE, HI-IMPACT,C6,BK,100FT |
| HIPE200W//GLASSGUARD | 制造商:VENTURE LIGHTING EUROPE LTD 功能描述:SHATTERPROOF LAMP 200W |
發布緊急采購，3分鐘左右您將得到回復。